LiftMaster Q183 / K15-50B16EES Sprocket — #50, 16 Teeth, 5/8-Inch Bore

LiftMaster Q183 / K15-50B16EES Sprocket — #50, 16 Teeth, 5/8-Inch Bore

$47.21
Skip to product information
LiftMaster Q183 / K15-50B16EES Sprocket — #50, 16 Teeth, 5/8-Inch Bore

LiftMaster Q183 / K15-50B16EES Sprocket — #50, 16 Teeth, 5/8-Inch Bore

Q183
$47.21
Shipping calculated at checkout.

The LiftMaster Q183 supplier SKU identifies K15-50B16EES, a 16-tooth sprocket for #50 roller chain with a 5/8-inch bore. Manufacturer CSW200 service information identifies this reference within the documented drive arrangement. Match the installed shaft, sprocket position and retention details before ordering; a matching chain size does not establish that every #50 sprocket will fit. This is an individual transmission component, and the condition of the mating chain and shaft matters as much as the replacement sprocket itself.

Compatibility — Models, Versions and Exclusions

Model or selection point Compatibility requirement
CSW200 arrangements specifying K15-50B16EES Match the exact repair drawing and shaft position.
#50 roller chain Correct chain family; length and remaining drive details must match.
5/8-inch shaft interface Confirm hub, retention and actual shaft condition.
Other tooth counts or bore sizes Not equivalent just because they accept #50 chain.
K15-3619 Different service reference; not an interchangeable sprocket.

Identify the Chain Family Before Comparing Shaft Dimensions

Record the existing sprocket number and photograph its position before disassembly. Check the tooth count, shaft diameter, hub offset and retention method against the operator drawing. A drive can contain several sprockets, so the correct chain size alone will not identify the correct location. Do not change the tooth count to alter operator speed or compensate for a worn drive.

Have the technician inspect the mating chain, adjacent sprockets and shaft for wear or damage. A new sprocket can perform poorly if installed with an elongated chain or a damaged shaft connection. Restore the documented alignment and tension instead of overtightening the chain to suppress noise. The gate must move freely on its own supports so the repaired transmission is not forced to overcome binding.

Specifications and Product Identification

Specification Details
Supplier SKU Q183
Manufacturer reference K15-50B16EES
Chain size #50
Tooth count 16
Bore 5/8 inch
Application Documented CSW200 drive arrangements; verify revision

Before Ordering

  • Match supplier Q183 to manufacturer K15-50B16EES.
  • Verify 16 teeth, #50 chain and the 5/8-inch bore.
  • Compare hub position and the complete shaft-retention arrangement.
  • Inspect chain wear and confirm any separate connecting or retaining parts.

Package Contents and Separate Requirements

This offer identifies the Q183 / K15-50B16EES sprocket. Chain, connecting links, shaft, gear reducer and a complete retention-hardware package are not promised as included. Confirm the current carton for any supplied key or fastening pieces. A drawing that shows the sprocket beside other drive parts does not make those parts part of this order; identify additional repair components individually before scheduling the work.

Safety Warnings — Read Before Installation or Service

  • WARNING: Exposed chain drives can entangle clothing or trap fingers and cause serious injury. Use a qualified door- or gate-systems technician.
  • Isolate all applicable power and secure the moving equipment before removing a chain or sprocket.
  • Do not enlarge the bore, improvise the shaft connection or substitute a different chain family to make a part fit.
  • Restore guards and complete the equipment’s prescribed operating and safety tests before normal use.

Related Products and Important Differences

  • #50 roller chain — a matching chain-family option; determine the required installed length.
  • #50 master link — a separate joining component for the correctly selected chain.

Frequently Asked Questions

How many teeth does it have?

The K15-50B16EES reference identifies 16 teeth.

Which chain size is specified?

#50 roller chain; the rest of the drive must also match.

Is the bore 5/8 inch?

Yes. Check the hub and retention details as well.

Can another #50 sprocket replace it?

Not without matching the exact service requirements, including tooth count and shaft interface.

Need Help Confirming the Right Product?

Contact Garage-DoorParts.com before ordering. Send the full equipment model, readable part labels and photographs of the installed assembly. Include the dimensions, electrical configuration or accessory details relevant to your project so the listing can be checked against the actual installation.

Details

Need Help With Compatibility?

Not sure if this is the correct part for your garage door, operator, gate system, or application? Contact Us before ordering — we’re happy to help.

Garage-DoorParts.com carries a large selection of residential and commercial parts, and many components can look similar while having important differences in dimensions, model numbers, voltage, mounting, or compatibility.

For the best assistance, please provide as much information as possible, including the manufacturer, model number, part number, door or operator type, dimensions, and clear photos of the existing part or equipment.

Our goal is to help you identify the correct product before you order and reduce the possibility of ordering an incompatible part.

Contact Us with your product questions and compatibility information, and we’ll do our best to point you in the right direction.

Shipping & Returns

We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.

We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.

Related products