LiftMaster K75-36913 Electrical-Box Cover — J, H and HJ Logic 5.0
The LiftMaster K75-36913 is the electrical-box cover identified in the documented J, H and HJ Logic 5.0 commercial-operator parts arrangement. It restores the specified enclosure cover and must match the actual control-box generation. It is separate from K75-36914 and from a complete electrical-box replacement kit. Confirm the installed model, enclosure and mounting points before ordering rather than selecting by a similar cover outline. Select the replacement by the complete part number and the installed equipment configuration. A similar photograph or a shared LiftMaster brand name does not establish interchangeability. Confirm the applicable service drawing before ordering so the repair addresses the correct component and its related mounting, connection and operating requirements.
Compatibility — Models, Versions and Exclusions
| Model or selection point | Compatibility requirement |
|---|---|
| J, H and HJ Logic 5.0 | Use the exact manufacturer drawing and installed enclosure. |
| Earlier Logic versions | Do not assume matching enclosure dimensions. |
| K75-36914 | Different service reference; no automatic interchangeability. |
| Complete electrical-box kit | Separate scope including components not supplied by a cover-only order. |
Identify the Assembly and Plan the Repair
Inspect the enclosure body, mounting points and internal wiring after any impact or heat damage. A cover should seat correctly without forcing it over bent supports or pinching conductors. If the box itself is distorted, a cover-only replacement may not restore the intended arrangement.
Retain the correct access, labels and wire clearances when restoring the enclosure. A replacement cover does not add a current-sense system, change the control generation or establish a new environmental rating. Confirm any screws, labels and wiring diagrams in the current package, then use the electrical documentation for the actual operator rather than a diagram associated with another cover.
An electrical symptom does not identify the failed component by itself. Have qualified service personnel inspect the supply, wiring, connections and equipment condition before replacing parts. Record existing labels and terminal references with power safely isolated. A replacement should restore the documented circuit arrangement; it should not be used to change operating voltage, defeat a protective function or compensate for a mechanical load that the equipment cannot safely move.
Compare the delivered item with the approved service reference before installation. The installer must obtain the equipment-specific wiring, mounting and commissioning instructions rather than infer them from the appearance of the part. Keep conductors clear of moving components and reinstall the intended covers. After the repair, check the original complaint and the equipment’s required operating and safety functions; a successful power-up alone is not a complete service test.
Specifications and Product Identification
| Specification | Details |
|---|---|
| Ordering reference | K75-36913 |
| Component | Electrical-box cover |
| Documented models | J, H and HJ |
| Control generation | Logic 5.0; match the exact revision |
| Separate cover reference | K75-36914 |
Before Ordering
- Confirm the complete model and Logic 5.0 enclosure.
- Match the exact cover reference.
- Inspect mounting and wiring clearances.
- Confirm current cover hardware and label inventory.
Package Contents and Separate Requirements
This offer identifies the electrical-box cover. Confirm mounting screws, labels and any supplied wiring diagrams with the current package. The enclosure body, logic board, power board, transformer, current-sense harness and complete operator are separate. A cover order does not renew all components shown behind it in the repair illustration.
Safety Warnings — Read Before Installation or Service
- WARNING: Electrical service can expose hazardous voltage and moving equipment. Use qualified service personnel and electrical personnel where required.
- Disconnect every applicable mains, battery and auxiliary supply before work. Follow the equipment instructions for stored energy and safe isolation.
- Do not force the cover over bent supports or pinch wiring. A cover replacement does not repair a damaged electrical box or add current sensing.
- Restore covers and wiring protection, then complete the model-specific functional and safety checks before returning the installation to normal use.
Related Products and Important Differences
- CPS-U monitored photo eyes — separate protection devices for approved commercial-door controls; match the operator and environment.
- TDC12X1BMC MAXUM trolley operator — a complete-operator comparison, not evidence that this legacy service part fits MAXUM.
Frequently Asked Questions
Is this a complete control box?
No. It identifies the cover service item.
Does it fit every Logic operator?
No. Match model, control generation and enclosure arrangement.
Will it add current sensing?
No. A cover does not provide the required electronics or harness.
Does a new cover repair a distorted enclosure?
No. The supporting box and internal damage need separate assessment.
Need Help Confirming the Right Product?
Contact Garage-DoorParts.com before ordering. Send the full equipment model, readable part labels and photographs of the installed assembly. Include the dimensions, electrical configuration or accessory details relevant to your project so the listing can be checked against the actual installation.
Details
Need Help With Compatibility?
Not sure if this is the correct part for your garage door, operator, gate system, or application? Contact Us before ordering — we’re happy to help.
Garage-DoorParts.com carries a large selection of residential and commercial parts, and many components can look similar while having important differences in dimensions, model numbers, voltage, mounting, or compatibility.
For the best assistance, please provide as much information as possible, including the manufacturer, model number, part number, door or operator type, dimensions, and clear photos of the existing part or equipment.
Our goal is to help you identify the correct product before you order and reduce the possibility of ordering an incompatible part.
Contact Us with your product questions and compatibility information, and we’ll do our best to point you in the right direction.
Shipping & Returns
We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.
We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.