LiftMaster K74-19499 Replacement Antenna — Legacy LA400 Control Arrangement
The LiftMaster K74-19499 is the antenna service reference identified in the legacy LA400/ LA400S control-box parts list. It restores the specified receiver-antenna arrangement and must match the installed control revision. It is separate from the radio receiver module, remotes and antenna-extension accessories. Replacing the antenna does not change receiver frequency, credential coding or opener generation, and it does not guarantee a particular operating distance. Select the replacement by the complete part number and the installed equipment configuration. A similar photograph or a shared LiftMaster brand name does not establish interchangeability. Confirm the applicable service drawing before ordering so the repair addresses the correct component and its related mounting, connection and operating requirements.
Compatibility — Models, Versions and Exclusions
| Model or selection point | Compatibility requirement |
|---|---|
| Legacy LA400 / LA400S drawing | Match the actual antenna connection and receiver arrangement. |
| Other LA400U / UL generations | Use their own exact service references. |
| Receiver-frequency changes | Antenna replacement does not establish a radio conversion. |
| Extension accessories | Separate requirements; no relocation cable assumed. |
Identify the Assembly and Plan the Repair
Inspect the antenna and receiver connection and diagnose interference or transmitter problems before assuming an antenna-only repair is needed. Reduced range can involve weak remote batteries, mounting location or another receiver fault. Record the existing component and control-box configuration.
Preserve the approved antenna route and mounting without improvised wire extensions or connector substitutions. If relocating the antenna is the project goal, obtain the correct documented extension arrangement. After repair, verify authorized remote operation from relevant approach positions while keeping the moving gate visible and clear.
An electrical symptom does not identify the failed component by itself. Have qualified service personnel inspect the supply, wiring, connections and equipment condition before replacing parts. Record existing labels and terminal references with power safely isolated. A replacement should restore the documented circuit arrangement; it should not be used to change operating voltage, defeat a protective function or compensate for a mechanical load that the equipment cannot safely move.
Compare the delivered item with the approved service reference before installation. The installer must obtain the equipment-specific wiring, mounting and commissioning instructions rather than infer them from the appearance of the part. Keep conductors clear of moving components and reinstall the intended covers. After the repair, check the original complaint and the equipment’s required operating and safety functions; a successful power-up alone is not a complete service test.
Specifications and Product Identification
| Specification | Details |
|---|---|
| Ordering reference | K74-19499 |
| Component | Antenna service item |
| Documented example | Legacy LA400 / LA400S control box |
| Separate receiver | K001A5747 or specified frequency variant |
| Range | Site dependent; no guaranteed distance assigned |
Before Ordering
- Confirm K74-19499 in the correct control-box drawing.
- Inspect antenna and receiver connection.
- Check transmitter condition and interference.
- Distinguish replacement from antenna relocation.
Package Contents and Separate Requirements
This offer identifies the antenna. Receiver module, remotes, mounting structure, extension cable and complete operator are separate unless expressly included. Confirm the current antenna and any connection pieces. A control-box diagram showing the antenna beside the board does not include the board or the complete radio system.
Safety Warnings — Read Before Installation or Service
- WARNING: Electrical service can expose hazardous voltage and moving equipment. Use qualified service personnel and electrical personnel where required.
- Disconnect every applicable mains, battery and auxiliary supply before work. Follow the equipment instructions for stored energy and safe isolation.
- Test radio commands only with the gate visible and clear. An antenna does not replace monitored protection or authorize unattended hazardous movement.
- Restore covers and wiring protection, then complete the model-specific functional and safety checks before returning the installation to normal use.
Related Products and Important Differences
- CPS-U monitored photo eyes — separate protection devices for approved commercial-door controls; match the operator and environment.
- TDC12X1BMC MAXUM trolley operator — a complete-operator comparison, not evidence that this legacy service part fits MAXUM.
Frequently Asked Questions
Will it change frequency?
No. The receiver determines the radio system.
Is an extension cable included?
No extension cable is established as included.
Is a range improvement guaranteed?
No. Reception depends on the complete installation and conditions.
Does it fit every LA400 generation?
No. Match the exact control and service reference.
Need Help Confirming the Right Product?
Contact Garage-DoorParts.com before ordering. Send the full equipment model, readable part labels and photographs of the installed assembly. Include the dimensions, electrical configuration or accessory details relevant to your project so the listing can be checked against the actual installation.
Details
Need Help With Compatibility?
Not sure if this is the correct part for your garage door, operator, gate system, or application? Contact Us before ordering — we’re happy to help.
Garage-DoorParts.com carries a large selection of residential and commercial parts, and many components can look similar while having important differences in dimensions, model numbers, voltage, mounting, or compatibility.
For the best assistance, please provide as much information as possible, including the manufacturer, model number, part number, door or operator type, dimensions, and clear photos of the existing part or equipment.
Our goal is to help you identify the correct product before you order and reduce the possibility of ordering an incompatible part.
Contact Us with your product questions and compatibility information, and we’ll do our best to point you in the right direction.
Shipping & Returns
We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.
We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.