LiftMaster K41-0440-000 TECHNA Barrier-Arm Bracket Kit — Verify Model-Specific Arrangement
The LiftMaster K41-0440-000 is the arm-bracket kit identified in TECHNA barrier-gate repair information. It is separate from the arm-mounting hardware, retention kit and spring modules. Current manufacturer parts information distinguishes the CBG/IBG bracket reference from a separate PBG bracket kit, so the full barrier model and actual arm configuration must be checked before ordering. A shared TECHNA family name does not establish universal bracket fit. Select the replacement by the complete part number and the installed equipment configuration. A similar photograph or a shared LiftMaster brand name does not establish interchangeability. Confirm the applicable service drawing before ordering so the repair addresses the correct component and its related mounting, connection and operating requirements.
Compatibility — Models, Versions and Exclusions
| Model or selection point | Compatibility requirement |
|---|---|
| Documented CBG / IBG arrangement | Match the actual bracket and operator drawing. |
| PBG arrangements | Use exact current instructions; separate bracket reference is identified. |
| K41-0449-000 hardware | Separate mounting-hardware service reference. |
| K41-0442-000 retention kit | Separate repair function and inventory. |
Identify the Assembly and Plan the Repair
Inspect the arm, shaft connection and bracket after an impact. A hardware-only problem, bent bracket and damaged output connection require different repairs. Confirm all affected pieces before purchasing so the new bracket is not installed on an unsuitable mating assembly.
Barrier balancing components can impose loads even while the operator is stationary. Have a qualified technician support the arm and secure the mechanism using the exact procedure before loosening attachment points. Do not infer fastener dimensions or substitute another model’s bracket to approximate arm alignment.
Compare the replacement with the installed service arrangement before dismantling the equipment. Photograph the part’s location and record the complete model and visible service numbers. Inspect the surrounding attachment points and mating components for wear, impact damage or misalignment. Replacing one worn item will not correct a damaged support or another component that continues to impose abnormal loads on the repaired assembly.
Plan the repair around the manufacturer’s instructions for the actual equipment revision. Confirm access, safe support and any separate hardware before removing the old part. After installation, restore the intended retention, alignment and guarding, then test the equipment under controlled conditions. The repair is complete only when the original fault has been addressed and the system’s required operating and protection functions have been checked.
Specifications and Product Identification
| Specification | Details |
|---|---|
| Ordering reference | K41-0440-000 |
| Component | Barrier-arm bracket kit |
| Platform | TECHNA; model-specific selection |
| CBG / IBG reference | K41-0440-000 in current parts information |
| Separate PBG reference | K41-0550-000; verify exact revision |
Before Ordering
- Record the full CBG,IBG or PBG model.
- Confirm the exact current bracket reference.
- Inspect arm, shaft and retention condition.
- Verify supplied hardware and safe service instructions.
Package Contents and Separate Requirements
This offer identifies the arm-bracket kit. Barrier arm, separate mounting-hardware kit, retention kit, spring module, reducer and complete operator are separate unless expressly included. Confirm the current carton’s bracket and fastening pieces. A complete barrier-arm illustration does not establish that all surrounding components ship with the kit.
Safety Warnings — Read Before Installation or Service
- WARNING: A moving gate and exposed techna barrier-arm bracket kit — verify model-specific arrangement can cause serious injury. Installation and service require a qualified gate-systems technician.
- Isolate AC power, batteries and any solar supply as applicable, and secure the gate against unexpected movement before work begins.
- Support and secure the barrier arm and stored spring/balancing loads before bracket work. Do not substitute another model’s bracket or defeat required retention.
- Restore all covers and guards, then verify travel endpoints, reversal and every required safety device before returning the gate to normal operation.
Related Products and Important Differences
- LMRRUL monitored photo eye — a separate protection option only where the exact operator and control revision approve it; not a universal legacy retrofit.
- LMWEKITU monitored wireless edge kit — a separate edge communication system for approved controls and resistive edges; not a replacement for this mechanical or electrical service part.
Frequently Asked Questions
Does it fit every TECHNA model?
No. Current parts information distinguishes the PBG bracket arrangement.
Is the separate retention kit included?
No combined package is promised.
Can it repair a bent shaft?
No. Mating damage needs separate assessment.
Can I select only by the arm’s appearance?
No. Match the full model and current bracket drawing.
Need Help Confirming the Right Product?
Contact Garage-DoorParts.com before ordering. Send the full equipment model, readable part labels and photographs of the installed assembly. Include the dimensions, electrical configuration or accessory details relevant to your project so the listing can be checked against the actual installation.
Details
Need Help With Compatibility?
Not sure if this is the correct part for your garage door, operator, gate system, or application? Contact Us before ordering — we’re happy to help.
Garage-DoorParts.com carries a large selection of residential and commercial parts, and many components can look similar while having important differences in dimensions, model numbers, voltage, mounting, or compatibility.
For the best assistance, please provide as much information as possible, including the manufacturer, model number, part number, door or operator type, dimensions, and clear photos of the existing part or equipment.
Our goal is to help you identify the correct product before you order and reduce the possibility of ordering an incompatible part.
Contact Us with your product questions and compatibility information, and we’ll do our best to point you in the right direction.
Shipping & Returns
We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.
We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.