LiftMaster K41-0250-000 Expansion-Board and Terminal-Block Mounting Plate — Industrial Slide

LiftMaster K41-0250-000 Expansion-Board and Terminal-Block Mounting Plate — Industrial Slide

$71.97
Skip to product information
LiftMaster K41-0250-000 Expansion-Board and Terminal-Block Mounting Plate — Industrial Slide

LiftMaster K41-0250-000 Expansion-Board and Terminal-Block Mounting Plate — Industrial Slide

K41-0250-000
$71.97
Shipping calculated at checkout.

The LiftMaster K41-0250-000 is the expansion-board and terminal-block plate identified in documented INSL24UL/IHSL24UL repair information. It supports the specified components in the control arrangement and must match the installed enclosure revision. The product name describes a mounting plate for those components; it does not establish that an expansion board or terminal block is included. Confirm the current kit inventory before ordering. Select the replacement by the complete part number and the installed equipment configuration. A similar photograph or a shared LiftMaster brand name does not establish interchangeability. Confirm the applicable service drawing before ordering so the repair addresses the correct component and its related mounting, connection and operating requirements.

Compatibility — Models, Versions and Exclusions

Model or selection point Compatibility requirement
Industrial slide drawing specifying this plate Match the exact model and mounting.
K41-0249-000 Different plate and component location.
Expansion-board replacement Separate electronic service decision.
Other enclosures No universal hole-pattern or clearance compatibility established.

Identify the Assembly and Plan the Repair

Inspect the plate, enclosure supports and attached components after impact or corrosion. A plate replacement can restore the intended support only if the surrounding enclosure and mounting points remain suitable. Do not conceal damaged electronics or distorted supports behind new mounting hardware.

Preserve the prescribed clearances, grounding where applicable and wire routing during transfer. The installer must confirm which boards, terminals and mounting pieces are retained or separately replaced. A mounting plate does not change control capabilities or repair an electrical fault in an attached board.

An electrical symptom does not identify the failed component by itself. Have qualified service personnel inspect the supply, wiring, connections and equipment condition before replacing parts. Record existing labels and terminal references with power safely isolated. A replacement should restore the documented circuit arrangement; it should not be used to change operating voltage, defeat a protective function or compensate for a mechanical load that the equipment cannot safely move.

Compare the delivered item with the approved service reference before installation. The installer must obtain the equipment-specific wiring, mounting and commissioning instructions rather than infer them from the appearance of the part. Keep conductors clear of moving components and reinstall the intended covers. After the repair, check the original complaint and the equipment’s required operating and safety functions; a successful power-up alone is not a complete service test.

Specifications and Product Identification

Specification Details
Ordering reference K41-0250-000
Component Expansion-board / terminal-block plate
Documented platform INSL24UL / IHSL24UL
Separate plate K41-0249-000 for power/control/relay arrangement
Electronics inventory Not established as included

Before Ordering

  • Confirm the full industrial operator and plate position.
  • Match K41-0250-000 versus K41-0249-000.
  • Inspect enclosure and component mounts.
  • Verify current hardware and separate electronics needs.

Package Contents and Separate Requirements

This offer identifies the mounting plate. Expansion board, terminal block, main board, harness, control enclosure and operator are separate unless expressly included. Confirm current standoffs, fasteners and other attachment pieces. An illustration of boards mounted to a plate does not make the electronics part of the plate-only order.

Safety Warnings — Read Before Installation or Service

  • WARNING: Electrical service can expose hazardous voltage and moving equipment. Use qualified service personnel and electrical personnel where required.
  • Disconnect every applicable mains, battery and auxiliary supply before work. Follow the equipment instructions for stored energy and safe isolation.
  • Preserve board clearance and wire routing. Do not improvise supports or treat the plate as a repair for failed electronics.
  • Restore covers and wiring protection, then complete the model-specific functional and safety checks before returning the installation to normal use.

Related Products and Important Differences

Frequently Asked Questions

Is an expansion board included?

No board inclusion is established.

Is it the power-board plate?

K41-0249-000 is a separate reference for that arrangement.

Will it repair a failed circuit?

No. Diagnose the electronics separately.

Can the plate be drilled to approximate fit?

Use the exact approved mounting arrangement instead of improvising fit.

Need Help Confirming the Right Product?

Contact Garage-DoorParts.com before ordering. Send the full equipment model, readable part labels and photographs of the installed assembly. Include the dimensions, electrical configuration or accessory details relevant to your project so the listing can be checked against the actual installation.

Details

Need Help With Compatibility?

Not sure if this is the correct part for your garage door, operator, gate system, or application? Contact Us before ordering — we’re happy to help.

Garage-DoorParts.com carries a large selection of residential and commercial parts, and many components can look similar while having important differences in dimensions, model numbers, voltage, mounting, or compatibility.

For the best assistance, please provide as much information as possible, including the manufacturer, model number, part number, door or operator type, dimensions, and clear photos of the existing part or equipment.

Our goal is to help you identify the correct product before you order and reduce the possibility of ordering an incompatible part.

Contact Us with your product questions and compatibility information, and we’ll do our best to point you in the right direction.

Shipping & Returns

We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.

We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.

Related products