LiftMaster K15-5032 BG790 #50 Sprocket — 32 Teeth, 1-1/2-Inch Bore

LiftMaster K15-5032 BG790 #50 Sprocket — 32 Teeth, 1-1/2-Inch Bore

$53.60
Skip to product information
LiftMaster K15-5032 BG790 #50 Sprocket — 32 Teeth, 1-1/2-Inch Bore

LiftMaster K15-5032 BG790 #50 Sprocket — 32 Teeth, 1-1/2-Inch Bore

K15-5032
$53.60
Shipping calculated at checkout.

The LiftMaster K15-5032 is the sprocket identified with a 50B32T designation and 1-1/2-inch by 1/2-inch shaft/keying description for the documented BG790 barrier-operator arrangement. Match the exact shaft and drive drawing before ordering. The #50 chain series, 32-tooth count, bore and keying must all suit the approved configuration rather than merely resemble another barrier sprocket. Select the replacement by the complete part number and the installed equipment configuration. A similar photograph or a shared LiftMaster brand name does not establish interchangeability. Confirm the applicable service drawing before ordering so the repair addresses the correct component and its related mounting, connection and operating requirements.

Compatibility — Models, Versions and Exclusions

Model or selection point Compatibility requirement
BG790 service drawing Match K15-5032 at the correct shaft location.
Chain series Confirm #50 chain and approved 32-tooth ratio.
Shaft and key Verify bore, keying and required retention geometry.
Other barrier drives No universal sprocket interchangeability is established.

Identify the Assembly and Plan the Repair

Inspect the mating chain, shaft and keyway before selecting a sprocket-only repair. A stretched chain, damaged shaft surface or poor alignment can affect a correct replacement. Identify the actual main and intermediate drive arrangement in the BG790 drawing rather than select from tooth count alone.

Confirm current supplied retention pieces and the complete hub and clearance requirements before dismantling the drive. Do not change tooth count to improvise a different speed or barrier capacity. Have qualified personnel secure the arm and stored balancing loads, restore the approved chain path and guarding and complete the required operator and protection checks after service.

Compare the replacement with the installed service arrangement before dismantling the equipment. Photograph the part’s location and record the complete model and visible service numbers. Inspect the surrounding attachment points and mating components for wear, impact damage or misalignment. Replacing one worn item will not correct a damaged support or another component that continues to impose abnormal loads on the repaired assembly.

Specifications and Product Identification

Specification Details
Ordering reference K15-5032
Component Roller-chain sprocket
Chain / tooth designation 50B32T: #50 chain, 32 teeth
Bore designation 1-1/2 inches
Keying designation 1/2 inch; verify exact shaft arrangement
Documented application BG790 barrier operator

Before Ordering

  • Record the complete equipment model, serial information and installed service reference.
  • Match K15-5032 at the correct shaft location.
  • Confirm #50 chain and approved 32-tooth ratio.
  • Verify bore, keying and required retention geometry.
  • Confirm the current supplied inventory and exact installation and final testing instructions.

Package Contents and Separate Requirements

This offer identifies the sprocket service component. A chain, shaft key, retaining hardware, intermediate or main shaft, complete drive assembly and operator are not established as included. Confirm the current sprocket inventory and obtain separately worn parts from the exact BG790 service arrangement.

Safety Warnings — Read Before Installation or Service

  • WARNING: A moving gate and exposed bg790 #50 sprocket — 32 teeth, 1-1/2-inch bore can cause serious injury. Installation and service require a qualified gate-systems technician.
  • Isolate AC power, batteries and any solar supply as applicable, and secure the gate against unexpected movement before work begins.
  • Keep people clear of the gate and drive during supervised testing. Never bypass required entrapment-protection devices or increase force to overcome a mechanical fault.
  • Restore all covers and guards, then verify travel endpoints, reversal and every required safety device before returning the gate to normal operation.

Related Products and Important Differences

  • LMRRUL monitored photo eye — a separate protection option only where the exact operator and control revision approve it; not a universal legacy retrofit.
  • LMWEKITU monitored wireless edge kit — a separate edge communication system for approved controls and resistive edges; not a replacement for this mechanical or electrical service part.

Frequently Asked Questions

Does 50 mean 50 teeth?

No. It identifies the chain series; 32T identifies the tooth count.

Does a matching bore prove fit?

No. Chain series, tooth count, keying, hub position and retention must also match.

Is a shaft key included?

No key is established as included. Confirm the current package and required key separately.

Can another tooth count increase capacity?

No conversion is established. Restore the approved complete drive ratio and barrier arrangement.

Need Help Confirming the Right Product?

Contact Garage-DoorParts.com before ordering. Send the full equipment model, readable part labels and photographs of the installed assembly. Include the dimensions, electrical configuration or accessory details relevant to your project so the listing can be checked against the actual installation.

Details

Need Help With Compatibility?

Not sure if this is the correct part for your garage door, operator, gate system, or application? Contact Us before ordering — we’re happy to help.

Garage-DoorParts.com carries a large selection of residential and commercial parts, and many components can look similar while having important differences in dimensions, model numbers, voltage, mounting, or compatibility.

For the best assistance, please provide as much information as possible, including the manufacturer, model number, part number, door or operator type, dimensions, and clear photos of the existing part or equipment.

Our goal is to help you identify the correct product before you order and reduce the possibility of ordering an incompatible part.

Contact Us with your product questions and compatibility information, and we’ll do our best to point you in the right direction.

Shipping & Returns

We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.

We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.

Related products