LiftMaster K15-19478 48B32T Sprocket — 1-1/2-Inch Bore
The LiftMaster K15-19478 identifies the 48B32T sprocket with a 1-1/2-inch bore listed in the documented commercial drive arrangement. The designation specifies the #48 chain series and 32 teeth, while the bore identifies the nominal shaft fit. Match the complete operator service drawing, mounting and retention arrangement before choosing it as an output-drive replacement. Select the replacement by the complete part number and the installed equipment configuration. A similar photograph or a shared LiftMaster brand name does not establish interchangeability. Confirm the applicable service drawing before ordering so the repair addresses the correct component and its related mounting, connection and operating requirements.
Compatibility — Models, Versions and Exclusions
| Model or selection point | Compatibility requirement |
|---|---|
| Matching service drawing | Use where K15-19478 or the documented 15-19478 reference is specified. |
| Chain selection | Match the #48 drive arrangement. |
| Shaft and mounting | Verify 1-1/2-inch bore and complete retention geometry. |
| Other tooth counts | Do not substitute a different ratio to change operator performance. |
Identify the Assembly and Plan the Repair
Sprocket fit depends on more than shaft diameter. The chain series, tooth count, mounting position and adjacent drive components must all match the approved arrangement. A different sprocket can alter drive behavior or fail to align with the chain even when it physically slides onto the shaft.
Inspect the chain, shaft, bearings and mating sprocket together. If a chain has worn unevenly or the drive is misaligned, replacing the sprocket alone can leave the original cause of wear in place. Obtain any missing hub or retention dimensions from the exact service drawing rather than guessing from the 48B32T designation.
Compare the replacement with the installed service arrangement before dismantling the equipment. Photograph the part’s location and record the complete model and visible service numbers. Inspect the surrounding attachment points and mating components for wear, impact damage or misalignment. Replacing one worn item will not correct a damaged support or another component that continues to impose abnormal loads on the repaired assembly.
Specifications and Product Identification
| Specification | Details |
|---|---|
| Ordering reference | K15-19478 |
| Sprocket designation | 48B32T |
| Chain series | #48 |
| Tooth count | 32 |
| Bore | 1-1/2 inches |
| Other dimensions | Confirm hub, keying and retention from current service information |
Before Ordering
- Confirm the complete sprocket service reference.
- Verify #48 chain, 32 teeth and 1-1/2-inch bore.
- Check hub position, shaft retention and clearances.
- Inspect the adjoining chain drive for wear and alignment.
Package Contents and Separate Requirements
This offer identifies the sprocket service component. Confirm current supplied retention hardware. A drive chain, shaft key, shaft, bearings, mating sprocket and complete output assembly are not established as included; the equipment-specific parts drawing determines the separate service requirements.
Safety Warnings — Read Before Installation or Service
- WARNING: A moving commercial door and exposed 48b32t sprocket — 1-1/2-inch bore can cause serious injury or death. Have a trained door-systems technician perform installation and service.
- Disconnect mains power and any battery backup before mechanical work or wiring. Secure the door against unexpected movement as directed by its manufacturer.
- Do not work on springs, cables or counterbalance components without appropriate training. Never bypass safety sensors or increase force to overcome binding.
- Restore guards and complete the model-specific travel, reversal and protection-device tests before returning the door to normal operation.
Related Products and Important Differences
- CPS-U monitored photo eyes — separate protection devices for approved commercial-door controls; match the operator and environment.
- TDC12X1BMC MAXUM trolley operator — a complete-operator comparison, not evidence that this legacy service part fits MAXUM.
Frequently Asked Questions
Does 48B32T mean 48 teeth?
No. The identified sprocket is for the #48 chain series and has 32 teeth.
Will a matching bore prove fit?
No. Chain series, tooth count, hub position, retention and the approved service application must also match.
Is a new chain included?
No chain is established as included. Inspect and order the correct chain separately when required.
Can I use another tooth count for more capacity?
Use the manufacturer’s approved drive ratio. A sprocket change is not an authorized operator capacity upgrade.
Need Help Confirming the Right Product?
Contact Garage-DoorParts.com before ordering. Send the full equipment model, readable part labels and photographs of the installed assembly. Include the dimensions, electrical configuration or accessory details relevant to your project so the listing can be checked against the actual installation.
Details
Need Help With Compatibility?
Not sure if this is the correct part for your garage door, operator, gate system, or application? Contact Us before ordering — we’re happy to help.
Garage-DoorParts.com carries a large selection of residential and commercial parts, and many components can look similar while having important differences in dimensions, model numbers, voltage, mounting, or compatibility.
For the best assistance, please provide as much information as possible, including the manufacturer, model number, part number, door or operator type, dimensions, and clear photos of the existing part or equipment.
Our goal is to help you identify the correct product before you order and reduce the possibility of ordering an incompatible part.
Contact Us with your product questions and compatibility information, and we’ll do our best to point you in the right direction.
Shipping & Returns
We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.
We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.