LiftMaster AUHM6 Black Gate Roller — 6-Inch, Bearing Not Included; Verify Material

LiftMaster AUHM6 Black Gate Roller — 6-Inch, Bearing Not Included; Verify Material

$73.44
Skip to product information
LiftMaster AUHM6 Black Gate Roller — 6-Inch, Bearing Not Included; Verify Material

LiftMaster AUHM6 Black Gate Roller — 6-Inch, Bearing Not Included; Verify Material

AUHM6
$73.44
Shipping calculated at checkout.

The LiftMaster AUHM6 is a six-inch black gate roller listed by the supplier without a bearing. The supplier calls the material neoprene, while LiftMaster’s parts catalog describes AUHM6 as a UHMW roller. These are different materials, so confirm the current supplied roller before ordering rather than treating either description as settled. Match the full roller dimensions, shaft interface and installed support arrangement as well. This is a mechanical replacement component, not a complete bracket, powered drive or monitored safety sensor.

Compatibility — Models, Versions and Exclusions

Model or selection point Compatibility requirement
Gate assemblies specifying this roller Match the complete hardware reference and measured fit.
Other six-inch guide or pinch rollers Nominal size alone does not establish width, shaft interface or mounting compatibility.
Bearing-equipped rollers Different package scope; this offer is expressly without a bearing.
Complete guide-roller brackets Separate mounting components, not included by the roller description.
Gate-support wheels Different function unless the actual hardware documentation specifies this roller.

Inspect the Roller Mounting and Gate Alignment

A worn roller can be accompanied by a damaged shaft, loose bracket or poor gate alignment. Inspect the entire contact arrangement before ordering the replacement. The roller should contact the gate only as intended by the installed design; excessive pressure is not a way to correct a bent frame or a gate that runs out of line. Record the original roller and mounting dimensions while the assembly is accessible.

Because this offer excludes a bearing, determine how the existing assembly is supported and which service pieces can legitimately be reused. Do not assume a bearing from a visually similar roller has the correct dimensions or retention. The new roller must have suitable clearance and rotate or function as the original design requires. A gate roller is a mechanical hardware component, not a monitored safety edge or other entrapment sensor.

Specifications and Product Identification

Specification Details
Supplier SKU AUHM6
Supplier part reference AUHM
Nominal size 6 inches
Color Black
Material discrepancy Supplier: neoprene; manufacturer catalog: UHMW — confirm current part
Bearing Supplier specifies not included

Before Ordering

  • Identify the original roller and its mounting function.
  • Verify all required dimensions rather than relying only on the six-inch description.
  • Inspect the shaft, bracket, retention and any separate bearing.
  • Check gate alignment and the required protection around the roller contact area.

Package Contents and Separate Requirements

This offer identifies the black gate roller without a bearing. A mounting bracket, shaft, bearing, retention hardware, gate wheel assembly and complete gate are not promised as included. Confirm the current package and exact dimensions before purchase if the installed part cannot be positively matched. The source’s single roller description does not establish a pair, a preassembled bracket kit or a load-capacity rating.

Safety Warnings — Read Before Installation or Service

  • WARNING: Gate rollers can create serious pinch and entrapment hazards. Qualified gate personnel must secure and support the gate before removing hardware.
  • Isolate operator power and prevent gate movement during service. Keep hands, clothing and tools away from roller contact points.
  • Do not remove required guards or position a replacement roller where it introduces an accessible hazard. Correct gate alignment and structural defects independently.
  • After repair, verify smooth movement, secure retention and the complete installation’s required protection devices before allowing normal use.

Related Products and Important Differences

  • LMRRUL monitored photo eye — a separate protection option only where the exact operator and control revision approve it; not a universal legacy retrofit.
  • LMWEKITU monitored wireless edge kit — a separate edge communication system for approved controls and resistive edges; not a replacement for this mechanical or electrical service part.

Frequently Asked Questions

Is a bearing included?

No. The source explicitly describes this roller as supplied without a bearing.

Does six inches establish every dimension?

No. Confirm the full roller and shaft-interface dimensions for the installed assembly.

Is this a safety sensor?

No. It is mechanical gate hardware and does not provide monitored entrapment detection.

Does the offer include the bracket?

No bracket or complete support assembly is promised by the roller-only description.

Which material will be supplied?

The supplier and manufacturer descriptions conflict. Confirm the actual supplied material before purchase.

Need Help Confirming the Right Product?

Contact Garage-DoorParts.com before ordering. Send the full equipment model, readable part labels and photographs of the installed assembly. Include the dimensions, electrical configuration or accessory details relevant to your project so the listing can be checked against the actual installation.

Details

Need Help With Compatibility?

Not sure if this is the correct part for your garage door, operator, gate system, or application? Contact Us before ordering — we’re happy to help.

Garage-DoorParts.com carries a large selection of residential and commercial parts, and many components can look similar while having important differences in dimensions, model numbers, voltage, mounting, or compatibility.

For the best assistance, please provide as much information as possible, including the manufacturer, model number, part number, door or operator type, dimensions, and clear photos of the existing part or equipment.

Our goal is to help you identify the correct product before you order and reduce the possibility of ordering an incompatible part.

Contact Us with your product questions and compatibility information, and we’ll do our best to point you in the right direction.

Shipping & Returns

We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.

We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.

Related products