SSC .2950 x 1.75" ID x 55" Torsion Spring – Right Wind (RW) – White

🇺🇸 Made in USA

This Right Wind (RW) torsion spring is manufactured by Service Spring Corporation (SSC) for sectional overhead door torsion systems requiring a .2950" wire size, 1.75" inside diameter, and 55" spring length.

Manufactured from coated, oil-tempered spring wire, this spring comes with the winding cone and stationary cone installed and is rated for an industry-standard minimum lifecycle of 10,000 cycles.

The .2950" wire size uses the White color code. Color should be used only as an identification aid—always verify the actual wire diameter, inside diameter, spring length, and wind direction before ordering.

Specifications

Application

Designed for torsion-spring counterbalance systems where the calculated requirements call for a Right Wind .2950" x 1.75" ID x 55" torsion spring.

This spring may be used in residential, commercial, or light-industrial sectional door systems when its torque characteristics correctly match the door weight, height, cable drums, track configuration, and overall counterbalance requirements.

Compatibility & Fitment

Torsion springs are not universal replacement parts.

Correct replacement requires matching or properly calculating:

• Wire diameter

• Inside diameter

• Spring length

• Wind direction

• Door weight

• Door height

• Cable drum type

• Track configuration

• Number of springs

• Required torque / IPPT

• Available shaft and spring space

Two torsion springs that appear similar can produce substantially different torque and should not be considered interchangeable without proper calculation.

Right-Wind Identification

This is a Right Wind (RW) torsion spring.

On a conventional torsion system, a right-wound spring is typically installed on the left side of the center support when viewed from inside the garage looking toward the door.

System configurations can vary, so always verify the actual winding direction rather than relying only on the spring's installed position.

White Wire Color Code

The White color code identifies the .2950" wire size.

Do not select a replacement torsion spring by color alone. White is also used for other torsion wire sizes, so the actual wire diameter must be confirmed.

For accurate replacement, physically verify:

• .2950" wire size

• 1.75" inside diameter

• 55" unwound spring length

• Right Wind direction

Important Matching Notes

When replacing one spring in a two-spring torsion system, inspect and identify the opposite spring as well.

Paired torsion springs normally use opposite wind directions, but the two springs are not necessarily identical in every application.

Changing wire size, inside diameter, or spring length changes the spring's torque characteristics. Alternate spring sizes should only be used after the door's counterbalance requirements have been properly calculated.

Cones Installed

This spring comes with both the winding cone and stationary cone already installed.

Proper torsion-spring installation requires correctly sized winding bars and knowledge of:

• Spring winding

• Shaft positioning

• Cable drum setup

• Cable tension

• Bearing alignment

• Door balancing

After installation, verify that the lift cables remain correctly seated on the drums and that the door is properly balanced throughout its travel.

Ready to Order?

If your existing spring matches the .2950" wire size, 1.75" inside diameter, 55" length, and Right Wind configuration, this SSC replacement spring is ready for your repair.

Add this spring to your cart today and restore proper counterbalance with the correct SSC-made replacement.

Before purchasing, double-check:

• .2950" wire size

• 1.75" inside diameter

• 55" spring length

• Right Wind (RW)

If any specification differs from your existing spring, verify the correct replacement before ordering.

Safety Warning

⚠️ Garage door torsion springs operate under extreme stored mechanical energy and can cause severe injury, death, or property damage if improperly installed, adjusted, or removed.

Installation and service should be performed only by a qualified person familiar with torsion-spring systems and using proper tools and procedures.

Never loosen a winding cone, stationary cone, cable drum, bearing plate, or related torsion-system component while the spring is under tension unless you understand the correct service procedure.

SEO Title: SSC .2950 x 1.75 ID x 55 Torsion Spring – Right Wind

Meta Description: SSC .2950 wire x 1.75" ID x 55" right-wind torsion spring. White color code, coated oil-tempered wire, cones installed, Made in USA.