SSC .2500 x 2″ ID x 36″ Torsion Spring – Right Wind – Gold
SSC .2500 x 2″ ID x 36″ Torsion Spring – Right Wind – Gold
🇺🇸 Made in USA
Manufactured by Service Spring Corporation (SSC), this .2500″ wire x 2″ inside diameter x 36″ right-wind torsion spring is intended for sectional door systems requiring this exact spring size and winding direction.
The spring includes installed winding and stationary cones and features coated, oil-tempered wire. Correct selection helps restore the counterbalance needed for smooth manual movement and proper opener operation.
Features & Benefits
-
.2500″ wire diameter with gold wire-size identification.
-
2″ inside diameter.
-
36″ unwound spring-body length, excluding cones.
-
Right-wind configuration.
-
Installed winding and stationary cones.
-
Coated, oil-tempered wire.
-
Stenciled and color-coded for identification.
-
Standard-cycle spring listed for a minimum 10,000-cycle application when correctly selected.
A cycle consists of one full opening and closing. Service life varies with spring loading, operating turns, installation, maintenance, and environmental conditions.
Specifications
| Specification | Detail |
|---|---|
| Manufacturer | SSC — Service Spring Corporation |
| Wire diameter | .2500″ |
| Inside diameter | 2″ |
| Spring-body length | 36″, unwound, excluding cones |
| Winding direction | Right Wind — RW |
| Wire-size color | Gold |
| Wire construction | Coated, oil-tempered |
| Cones | Winding and stationary cones installed |
| Cycle classification | Standard cycle; listed minimum 10,000 cycles |
Common Applications
For replacement of a matching torsion spring on a compatible sectional overhead door. Final suitability depends on actual door weight, door height, cable drums, lift configuration, and the complete spring combination.
The .2500″ wire size does not establish a specific door-weight capacity by itself.
Compatibility & Measurement
Match .2500″ wire diameter, 2″ inside diameter, 36″ unwound coil-body length, and right-wind direction. Verify shaft fit, cone mounting, and available operating clearance.
The 2″ measurement identifies the spring’s inside diameter, not the torsion-shaft diameter. Measure the spring body without the cones and do not substitute a nearby length without a compatibility calculation.
Right wind describes coil direction rather than simply the side of the opening where the spring belongs. The gold wire-size marking does not determine installation position.
Pairing & System Changes
For paired systems, both springs must provide the required combined torque. Some doors use equal-size opposite-wind springs; others use unequal sizes by design.
Have the companion inspected when replacing a failed spring, especially if both springs are the same age. Higher-cycle alternatives require a calculated size change that preserves the required output and fits the shaft.
High-lift or vertical-lift conversions and different cable drums change the counterbalance requirements and must be evaluated separately.
Installation & Safety
Professional installation is strongly recommended. Torsion springs and connected hardware can release dangerous stored energy if handled incorrectly.
Do not loosen loaded cones, drums, lifting cables, or bottom fixtures. A trained technician should follow the manufacturer’s procedures and verify balance, cable tracking, clearances, and opener safety operation after replacement.
Confirm your measurements and order this SSC 36-inch right-wind spring. Send us your spring and door-system details if you need help checking the match.
SSC .2500 x 2″ ID x 36″ Right-Wind Torsion Spring – Gold
American-made SSC torsion spring with coated, oil-tempered wire and installed cones. Match dimensions and right-wind configuration before purchasing.
Details
Need Help With Compatibility?
Not sure if this is the correct part for your garage door, operator, gate system, or application? Contact Us before ordering — we’re happy to help.
Garage-DoorParts.com carries a large selection of residential and commercial parts, and many components can look similar while having important differences in dimensions, model numbers, voltage, mounting, or compatibility.
For the best assistance, please provide as much information as possible, including the manufacturer, model number, part number, door or operator type, dimensions, and clear photos of the existing part or equipment.
Our goal is to help you identify the correct product before you order and reduce the possibility of ordering an incompatible part.
Contact Us with your product questions and compatibility information, and we’ll do our best to point you in the right direction.
Shipping & Returns
We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.
We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.
Shop The Full Collection
