SSC .2253 x 1.75″ ID x 27.5″ Torsion Spring – Right Wind – Red
SSC .2253 x 1.75″ ID x 27.5″ Torsion Spring – Right Wind – Red
🇺🇸 Made in USA
Manufactured by Service Spring Corporation (SSC), this .2253″ wire x 1.75″ inside diameter x 27.5″ right-wind torsion spring is a replacement for sectional door counterbalance systems requiring this exact configuration.
The spring features coated, oil-tempered wire and comes with winding and stationary cones installed. Its dimensions and winding direction must match the existing engineered arrangement or a professionally calculated replacement.
Features & Benefits
-
.2253″ wire diameter with red wire-size identification.
-
1.75″ inside diameter.
-
27.5″ unwound spring-body length.
-
Right-wind configuration.
-
Winding and stationary cones installed.
-
Coated, oil-tempered wire.
-
Stenciled and color-coded for identification.
-
Standard-cycle spring listed for a minimum 10,000-cycle application when correctly selected.
A cycle consists of one complete opening and closing. Service life varies with spring loading, operating turns, installation quality, maintenance, and environmental conditions.
Specifications
| Specification | Detail |
|---|---|
| Manufacturer | SSC — Service Spring Corporation |
| Wire diameter | .2253″ |
| Inside diameter | 1.75″ |
| Spring-body length | 27.5″, unwound, excluding cones |
| Winding direction | Right Wind — RW |
| Wire-size color | Red |
| Wire construction | Coated, oil-tempered |
| Cones | Winding and stationary cones installed |
| Cycle classification | Standard cycle; listed minimum 10,000 cycles |
Common Uses
For replacing a matching right-wind torsion spring on a compatible sectional overhead door. Door weight, height, drum geometry, lift configuration, and any companion spring determine the correct application.
Neither the red marking nor the .2253″ wire diameter establishes a universal lifting capacity.
Compatibility & Selection
Match .2253″ wire, 1.75″ inside diameter, 27.5″ unwound coil-body length, and right wind. Check shaft compatibility, cone fit, stationary mounting, and available operating space.
Right wind describes the direction of the spring coils; it does not simply mean the spring installs on the right side of the opening.
The left-wind version has a different coil direction and cannot be substituted at the same mounting position. Red wire-size paint is separate from the markings used to identify cone winding direction.
Pairing & System Requirements
For a two-spring assembly, confirm the required combined torque. A same-size left-wind companion is suitable only when that pair matches the system design; some doors require unequal spring sizes.
If both springs are the same age, have the companion inspected when replacing a failed spring. Higher-cycle upgrades require an engineered alternative with appropriate output and sufficient shaft clearance.
High-lift tracks, vertical-lift operation, and changes to cable drums alter counterbalance requirements and must be assessed separately.
Installation & Safety
Installation and adjustment should be performed by a trained garage door technician using proper winding bars and manufacturer-approved procedures.
Never loosen loaded spring cones, cable drums, lifting cables, or bottom fixtures. Following replacement, verify manual door balance throughout travel, cable seating, hardware clearances, and opener safety operation.
Order this SSC right-wind spring once its dimensions and system fit are confirmed. Send us your measurements and door-system details if you need help checking compatibility before purchasing.
SSC .2253 x 1.75″ ID x 27.5″ Right-Wind Torsion Spring – Red
Shop an American-made SSC torsion spring with coated wire and installed cones. Verify exact size and right-wind configuration before ordering.
Details
Need Help With Compatibility?
Not sure if this is the correct part for your garage door, operator, gate system, or application? Contact Us before ordering — we’re happy to help.
Garage-DoorParts.com carries a large selection of residential and commercial parts, and many components can look similar while having important differences in dimensions, model numbers, voltage, mounting, or compatibility.
For the best assistance, please provide as much information as possible, including the manufacturer, model number, part number, door or operator type, dimensions, and clear photos of the existing part or equipment.
Our goal is to help you identify the correct product before you order and reduce the possibility of ordering an incompatible part.
Contact Us with your product questions and compatibility information, and we’ll do our best to point you in the right direction.
Shipping & Returns
We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.
We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.
Shop The Full Collection
