LiftMaster Q198 Swivel Service Component — K75-50214, Legacy Swing-Gate Arm
The LiftMaster Q198 supplier reference identifies the swivel-only service component mapped to K75-50214 in documented legacy swing-gate arm information. It is one part of the specified arm arrangement, separate from the complete Q103 swivel-arm kit, arm extension and gate bracket. Match the exact operator generation and pivot connection before ordering rather than treating a swivel-only offer as a complete replacement linkage. Select the replacement by the complete part number and the installed equipment configuration. A similar photograph or a shared LiftMaster brand name does not establish interchangeability. Confirm the applicable service drawing before ordering so the repair addresses the correct component and its related mounting, connection and operating requirements.
Compatibility — Models, Versions and Exclusions
| Model or selection point | Compatibility requirement |
|---|---|
| Legacy arm drawings specifying Q198 | Match the operator and pivot arrangement. |
| Q103 complete swivel-arm kit | Different repair scope and inventory. |
| Other swing-gate linkage designs | No automatic interchangeability. |
| Worn arm or bracket interfaces | Require separate inspection beyond the swivel. |
Identify the Assembly and Plan the Repair
Inspect the connected arm, pivot and gate attachment if the swivel is loose or binding. A replacement swivel cannot restore a worn bore, distorted bracket or damaged arm connection. Identify whether the fault is isolated to this piece or whether a larger arm assembly is required.
Follow the exact operator’s procedure for supporting the gate and securing the linkage during service. Preserve the intended pivot geometry and retention and do not improvise a different arm position to approximate fit. Check smooth movement throughout the required travel and verify the complete gate protection arrangement after reassembly.
Compare the replacement with the installed service arrangement before dismantling the equipment. Photograph the part’s location and record the complete model and visible service numbers. Inspect the surrounding attachment points and mating components for wear, impact damage or misalignment. Replacing one worn item will not correct a damaged support or another component that continues to impose abnormal loads on the repaired assembly.
Plan the repair around the manufacturer’s instructions for the actual equipment revision. Confirm access, safe support and any separate hardware before removing the old part. After installation, restore the intended retention, alignment and guarding, then test the equipment under controlled conditions. The repair is complete only when the original fault has been addressed and the system’s required operating and protection functions have been checked.
Specifications and Product Identification
| Specification | Details |
|---|---|
| Ordering reference | Q198 |
| Supplier SKU | Q198 |
| Manufacturer reference | K75-50214 |
| Product role | Swivel-only service component |
| Separate larger assembly | Q103 swivel-arm kit |
Before Ordering
- Match Q198 to K75-50214.
- Confirm the legacy operator and arm drawing.
- Inspect all mating pivots and attachments.
- Compare swivel-only versus complete-arm repair requirements.
Package Contents and Separate Requirements
This listing identifies the swivel-only service item. Complete arm, extension, gate bracket, pivot hardware and operator are separate unless explicitly included. Confirm the current supplied fastening pieces. A picture of the assembled linkage does not make the whole Q103 arm assembly part of this smaller service order.
Safety Warnings — Read Before Installation or Service
- WARNING: A moving gate and exposed swivel service component — k75-50214, legacy swing-gate arm can cause serious injury. Installation and service require a qualified gate-systems technician.
- Isolate AC power, batteries and any solar supply as applicable, and secure the gate against unexpected movement before work begins.
- Secure the gate and support the linkage before loosening the swivel. Keep hands clear of pivot pinch points and restore the prescribed retention.
- Restore all covers and guards, then verify travel endpoints, reversal and every required safety device before returning the gate to normal operation.
Related Products and Important Differences
- LMRRUL monitored photo eye — a separate protection option only where the exact operator and control revision approve it; not a universal legacy retrofit.
- LMWEKITU monitored wireless edge kit — a separate edge communication system for approved controls and resistive edges; not a replacement for this mechanical or electrical service part.
Frequently Asked Questions
Is it the complete Q103 assembly?
No. This is the swivel-only reference.
What manufacturer number corresponds to it?
The documented mapping is K75-50214.
Will it repair a damaged arm bore?
No. Mating damage requires separate assessment.
Can it be chosen solely by operator brand?
No. Match the exact linkage generation and connection.
Need Help Confirming the Right Product?
Contact Garage-DoorParts.com before ordering. Send the full equipment model, readable part labels and photographs of the installed assembly. Include the dimensions, electrical configuration or accessory details relevant to your project so the listing can be checked against the actual installation.
Details
Need Help With Compatibility?
Not sure if this is the correct part for your garage door, operator, gate system, or application? Contact Us before ordering — we’re happy to help.
Garage-DoorParts.com carries a large selection of residential and commercial parts, and many components can look similar while having important differences in dimensions, model numbers, voltage, mounting, or compatibility.
For the best assistance, please provide as much information as possible, including the manufacturer, model number, part number, door or operator type, dimensions, and clear photos of the existing part or equipment.
Our goal is to help you identify the correct product before you order and reduce the possibility of ordering an incompatible part.
Contact Us with your product questions and compatibility information, and we’ll do our best to point you in the right direction.
Shipping & Returns
We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.
We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.