LiftMaster Q021 / K17-50095 Gear Pulley — SL3000
The LiftMaster Q021 supplier SKU identifies gear pulley K17-50095 for documented SL3000 slide-gate drive arrangements. Manufacturer parts information describes a 2-1/2-inch outside diameter and 5/8-inch bore. This is the pulley at the gear-drive position, so it should not be confused with a motor pulley that happens to have a similar outside diameter. Match the installed shaft, pulley location and exact service reference before ordering, and inspect the belt path to determine whether additional drive components need attention.
Compatibility — Models, Versions and Exclusions
| Model or selection point | Compatibility requirement |
|---|---|
| SL3000 configurations specifying Q021 | Match the correct gear-drive position and installed shaft. |
| Q025 / K17-50098 motor pulley | Different service position and bore specification. |
| Other 2-1/2-inch pulleys | Diameter alone does not establish shaft or belt fit. |
| CSW200 or newer slide platforms | No family-wide substitution is established by this listing. |
Identify the Gear Pulley Before Comparing Dimensions
Locate the pulley in the SL3000 service drawing and photograph the shaft and retention arrangement before parts are removed. Two pulleys can look similar from the front while using different shaft bores or hub geometry. Have the technician verify the actual connection and the supplied service reference. Do not enlarge a bore, add an improvised sleeve or change the drive ratio to accommodate the wrong part.
Inspect the belt, mating pulley, shaft condition and mounting security during the same repair. Uneven belt wear or repeated slipping can indicate poor alignment, damaged grooves or excessive mechanical load. Replacing a pulley does not correct a gate that binds on its track. Restore the approved drive geometry and use the manufacturer’s adjustment procedure before supervised operation.
Specifications and Product Identification
| Specification | Details |
|---|---|
| Supplier SKU | Q021 |
| Manufacturer reference | K17-50095 |
| Component | Gear pulley |
| Outside diameter | 2-1/2 inches |
| Bore | 5/8 inch |
| Documented family | SL3000; verify exact configuration |
Before Ordering
- Record the full SL3000 model and identify the gear-pulley position.
- Match Q021 / K17-50095 and confirm the 5/8-inch shaft interface.
- Inspect the belt path, mating pulley and retention arrangement.
- Confirm any separately required key or mounting pieces.
Package Contents and Separate Requirements
This offer identifies the gear pulley. A gear reducer, motor, belt, shaft key and complete retention-hardware set are not promised as included. Confirm the delivered package and required reusable components with the service drawing. The pulley is one part of the drive; a photograph or diagram showing the surrounding motor and gearbox does not make those assemblies part of this order.
Safety Warnings — Read Before Installation or Service
- WARNING: A moving gate and exposed belt and pulley drive can cause serious injury. Installation and service require a qualified gate-systems technician.
- Isolate AC power, batteries and any solar supply as applicable, and secure the gate against unexpected movement before work begins.
- Keep people clear of the gate and drive during supervised testing. Never bypass required entrapment-protection devices or increase force to overcome a mechanical fault.
- Restore all covers and guards, then verify travel endpoints, reversal and every required safety device before returning the gate to normal operation.
Related Products and Important Differences
- LMRRUL monitored photo eye — a separate protection option only where the exact operator and control revision approve it; not a universal legacy retrofit.
- LMWEKITU monitored wireless edge kit — a separate edge communication system for approved controls and resistive edges; not a replacement for this mechanical or electrical service part.
Frequently Asked Questions
Is this the Q025 motor pulley?
No. Q021 maps to K17-50095 at the gear-drive position.
What bore is specified?
Manufacturer parts information identifies 5/8 inch; verify the actual shaft before fitting.
Can any pulley with the same outside diameter replace it?
No. Bore, hub, retention and belt arrangement must also match.
Is a belt included?
No belt is promised with this pulley offer.
Need Help Confirming the Right Product?
Contact Garage-DoorParts.com before ordering. Send the full equipment model, readable part labels and photographs of the installed assembly. Include the dimensions, electrical configuration or accessory details relevant to your project so the listing can be checked against the actual installation.
Details
Need Help With Compatibility?
Not sure if this is the correct part for your garage door, operator, gate system, or application? Contact Us before ordering — we’re happy to help.
Garage-DoorParts.com carries a large selection of residential and commercial parts, and many components can look similar while having important differences in dimensions, model numbers, voltage, mounting, or compatibility.
For the best assistance, please provide as much information as possible, including the manufacturer, model number, part number, door or operator type, dimensions, and clear photos of the existing part or equipment.
Our goal is to help you identify the correct product before you order and reduce the possibility of ordering an incompatible part.
Contact Us with your product questions and compatibility information, and we’ll do our best to point you in the right direction.
Shipping & Returns
We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.
We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.