LiftMaster Q006 PC-Board Mounting Hardware Set — Verify Current Inventory
The LiftMaster Q006 supplier offer is the PC-board mounting-hardware set called PC board nuts in legacy operator instructions. Manufacturer service mapping associates it with K80-50044, described as control-board standoffs. Match the actual board support and supplied inventory before ordering. It is a mechanical mounting item, separate from the circuit board and electrical terminals, and must preserve the intended support and clearance arrangement. Select the replacement by the complete part number and the installed equipment configuration. A similar photograph or a shared LiftMaster brand name does not establish interchangeability. Confirm the applicable service drawing before ordering so the repair addresses the correct component and its related mounting, connection and operating requirements.
Compatibility — Models, Versions and Exclusions
| Model or selection point | Compatibility requirement |
|---|---|
| Legacy HCT / supported board mounts | Match the exact diagram and installed support. |
| Other control-board generations | Do not assume identical height or attachment. |
| Ordinary metal nuts | No equivalent insulation or mounting geometry established. |
| Circuit-board repair | Mounting hardware does not repair failed electronics. |
Identify the Assembly and Plan the Repair
Inspect the mounting points and board before replacing hardware. Broken or missing supports may allow movement or contact with surrounding components. A new support should restore the specified position without bending the board or using improvised spacers.
Legacy and newer catalogs use different descriptions for this mapping, so compare the current supplied pieces with the installed arrangement. Do not assume an old nuts label establishes a generic threaded fastener or that a stated installed quantity equals the number in every service package. Preserve the manufacturer’s board clearance and cable routing.
An electrical symptom does not identify the failed component by itself. Have qualified service personnel inspect the supply, wiring, connections and equipment condition before replacing parts. Record existing labels and terminal references with power safely isolated. A replacement should restore the documented circuit arrangement; it should not be used to change operating voltage, defeat a protective function or compensate for a mechanical load that the equipment cannot safely move.
Compare the delivered item with the approved service reference before installation. The installer must obtain the equipment-specific wiring, mounting and commissioning instructions rather than infer them from the appearance of the part. Keep conductors clear of moving components and reinstall the intended covers. After the repair, check the original complaint and the equipment’s required operating and safety functions; a successful power-up alone is not a complete service test.
Specifications and Product Identification
| Specification | Details |
|---|---|
| Ordering reference | Q006 |
| Supplier reference | Q006 |
| Legacy name | PC board nuts, one set |
| Manufacturer mapping | K80-50044 control-board standoffs |
| Current inventory | Verify supplied style and quantity |
Before Ordering
- Match Q006 and the documented K80-50044 mapping.
- Inspect board attachment and support condition.
- Verify supplied hardware style and quantity.
- Check required board clearance and wire routing.
Package Contents and Separate Requirements
The offer identifies one mounting-hardware set. Confirm its current standoff/nut inventory with the supplier. Circuit board, enclosure, complete harness and operator are separate. A diagram showing several supports around a board does not include the board or establish the carton quantity without the exact service-kit offer.
Safety Warnings — Read Before Installation or Service
- WARNING: Electrical service can expose hazardous voltage and moving equipment. Use qualified service personnel and electrical personnel where required.
- Disconnect every applicable mains, battery and auxiliary supply before work. Follow the equipment instructions for stored energy and safe isolation.
- Restore the specified board support and clearance. Do not improvise metal spacers or allow the board or wiring to contact unsuitable enclosure surfaces.
- Restore covers and wiring protection, then complete the model-specific functional and safety checks before returning the installation to normal use.
Related Products and Important Differences
- CPS-U monitored photo eyes — separate protection devices for approved commercial-door controls; match the operator and environment.
- TDC12X1BMC MAXUM trolley operator — a complete-operator comparison, not evidence that this legacy service part fits MAXUM.
Frequently Asked Questions
Is the board included?
No. This is mounting hardware.
Why are two hardware names used?
Legacy instructions say PC board nuts; the manufacturer service mapping describes standoffs.
Can ordinary nuts substitute?
Use the exact approved support arrangement and clearances.
Does it fix a failed circuit?
No. Diagnose board electronics separately.
Need Help Confirming the Right Product?
Contact Garage-DoorParts.com before ordering. Send the full equipment model, readable part labels and photographs of the installed assembly. Include the dimensions, electrical configuration or accessory details relevant to your project so the listing can be checked against the actual installation.
Details
Need Help With Compatibility?
Not sure if this is the correct part for your garage door, operator, gate system, or application? Contact Us before ordering — we’re happy to help.
Garage-DoorParts.com carries a large selection of residential and commercial parts, and many components can look similar while having important differences in dimensions, model numbers, voltage, mounting, or compatibility.
For the best assistance, please provide as much information as possible, including the manufacturer, model number, part number, door or operator type, dimensions, and clear photos of the existing part or equipment.
Our goal is to help you identify the correct product before you order and reduce the possibility of ordering an incompatible part.
Contact Us with your product questions and compatibility information, and we’ll do our best to point you in the right direction.
Shipping & Returns
We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.
We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.