LiftMaster PRE-SENSOR Trailer-Presence Sensor — Dock Status Accessory
The LiftMaster PRE-SENSOR is the trailer-presence sensor identified for the documented dock-management arrangement. The DDO8900W instructions describe it as a status sensor that indicates whether a trailer is present at the dock through the applicable LMi5 interface arrangement. Select it for the exact supported system rather than assume that a presence-status accessory is a substitute for door safety sensors or a vehicle-restraint mechanism. Select the replacement by the complete part number and the installed equipment configuration. A similar photograph or a shared LiftMaster brand name does not establish interchangeability. Confirm the applicable service drawing before ordering so the repair addresses the correct component and its related mounting, connection and operating requirements.
Compatibility — Models, Versions and Exclusions
| Model or selection point | Compatibility requirement |
|---|---|
| Approved dock-management setup | Confirm the current PRE-SENSOR system recommendation. |
| LMi5 interface | Follow its supported sensor and input requirements. |
| Door entrapment protection | Status monitoring does not replace required protection devices. |
| Other controls or sites | No universal dry-contact, voltage or network compatibility is established. |
Identify the Assembly and Plan the Repair
Plan the sensor location and connection as part of the complete dock installation. Confirm which equipment supplies the sensor and how its status is received by the approved interface. The DDO8900W documentation distinguishes trailer-presence sensing from restraint or leveler-position sensing, so choose the accessory for the actual information required rather than treat every dock sensor as interchangeable.
Obtain the current PRE-SENSOR installation instructions and the exact interface documentation before wiring. Do not infer detection distance, voltage, environmental rating or included power supply from the short product title. Qualified personnel should verify the installed status response under representative dock conditions and preserve the site’s required operating procedures. Sensor status does not by itself prove that a trailer is secured or that loading can safely begin.
An electrical symptom does not identify the failed component by itself. Have qualified service personnel inspect the supply, wiring, connections and equipment condition before replacing parts. Record existing labels and terminal references with power safely isolated. A replacement should restore the documented circuit arrangement; it should not be used to change operating voltage, defeat a protective function or compensate for a mechanical load that the equipment cannot safely move.
Specifications and Product Identification
| Specification | Details |
|---|---|
| Ordering reference | PRE-SENSOR |
| Component | Trailer-presence status sensor |
| Documented context | DDO8900W / LMi5 dock-management arrangement |
| Reported status | Trailer present or absent at the dock |
| Separate interface | LMi5; confirm required system configuration |
| Electrical requirements | Use the current sensor and interface instructions |
Before Ordering
- Identify the dock operator, interface and required status function.
- Confirm the current PRE-SENSOR compatibility recommendation.
- Verify power, input type and mounting from the exact instructions.
- Plan trailer-present/absent status tests and site procedures.
Package Contents and Separate Requirements
This offer identifies the trailer-presence sensor accessory. Confirm current sensor, mounting and connection pieces supplied. An LMi5 interface, external power supply, restraint, dock leveler, door safety-sensor set, network equipment and dock operator are not established as included. Check any separate system-service requirements before installation.
Safety Warnings — Read Before Installation or Service
- WARNING: Electrical service can expose hazardous voltage and moving equipment. Use qualified service personnel and electrical personnel where required.
- Disconnect every applicable mains, battery and auxiliary supply before work. Follow the equipment instructions for stored energy and safe isolation.
- Trailer-presence status does not prove that a vehicle is secured or that loading is safe. Preserve site dock procedures and all required door and restraint protection.
- Restore covers and wiring protection, then complete the model-specific functional and safety checks before returning the installation to normal use.
Related Products and Important Differences
- CPS-U monitored photo eyes — separate protection devices for approved commercial-door controls; match the operator and environment.
- TDC12X1BMC MAXUM trolley operator — a complete-operator comparison, not evidence that this legacy service part fits MAXUM.
Frequently Asked Questions
Does it sense whether a trailer is at the dock?
That is its documented status function in the supported dock-management arrangement.
Does it secure the trailer?
No restraint mechanism is established. Presence status does not prove that a trailer is secured.
Is it a replacement for door safety sensors?
No. Retain all required door protection and approved operating controls.
Are sensor voltage and range specified here?
No unverified values are claimed. Follow the current PRE-SENSOR and interface instructions for the actual installation.
Need Help Confirming the Right Product?
Contact Garage-DoorParts.com before ordering. Send the full equipment model, readable part labels and photographs of the installed assembly. Include the dimensions, electrical configuration or accessory details relevant to your project so the listing can be checked against the actual installation.
Details
Need Help With Compatibility?
Not sure if this is the correct part for your garage door, operator, gate system, or application? Contact Us before ordering — we’re happy to help.
Garage-DoorParts.com carries a large selection of residential and commercial parts, and many components can look similar while having important differences in dimensions, model numbers, voltage, mounting, or compatibility.
For the best assistance, please provide as much information as possible, including the manufacturer, model number, part number, door or operator type, dimensions, and clear photos of the existing part or equipment.
Our goal is to help you identify the correct product before you order and reduce the possibility of ordering an incompatible part.
Contact Us with your product questions and compatibility information, and we’ll do our best to point you in the right direction.
Shipping & Returns
We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.
We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.