LiftMaster MA002 Removable Twelve-Pin Connector — Mega Arm Control Arrangement
The LiftMaster MA002 is the removable twelve-pin connector identified in documented Mega Arm controller arrangements. It provides the specified electrical connection interface and must match the installed board and wiring configuration. It is separate from MA002J four-pin connector references and from the controller itself. Pin count alone does not establish that a generic connector has the required pitch, keying, terminal capacity or circuit assignment. Select the replacement by the complete part number and the installed equipment configuration. A similar photograph or a shared LiftMaster brand name does not establish interchangeability. Confirm the applicable service drawing before ordering so the repair addresses the correct component and its related mounting, connection and operating requirements.
Compatibility — Models, Versions and Exclusions
| Model or selection point | Compatibility requirement |
|---|---|
| Controller drawing specifying MA002 | Match the board revision and connector position. |
| MA002J | Different four-pin item; not interchangeable. |
| Generic twelve-pin plugs | Pitch, keying and approved wiring must also agree. |
| Main control board | Separate service scope and diagnostic role. |
Identify the Assembly and Plan the Repair
Record the terminal references and wiring before disconnecting the plug, with power safely isolated. If heat or corrosion has damaged the connection, inspect both the removable connector and its mating board interface. A new plug cannot repair damaged board contacts or correct the cause of overheating.
Use the exact operator wiring diagram and component instructions for conductor preparation and termination. Do not infer current ratings, wire gauge or tightening torque from a visually similar connector. Preserve circuit assignments and route conductors clear of moving or hot components before completing the required operator tests.
An electrical symptom does not identify the failed component by itself. Have qualified service personnel inspect the supply, wiring, connections and equipment condition before replacing parts. Record existing labels and terminal references with power safely isolated. A replacement should restore the documented circuit arrangement; it should not be used to change operating voltage, defeat a protective function or compensate for a mechanical load that the equipment cannot safely move.
Compare the delivered item with the approved service reference before installation. The installer must obtain the equipment-specific wiring, mounting and commissioning instructions rather than infer them from the appearance of the part. Keep conductors clear of moving components and reinstall the intended covers. After the repair, check the original complaint and the equipment’s required operating and safety functions; a successful power-up alone is not a complete service test.
Specifications and Product Identification
| Specification | Details |
|---|---|
| Ordering reference | MA002 |
| Component | Removable connector |
| Positions | Twelve pins |
| Documented example | Mega Arm control arrangement |
| Separate reference | MA002J four-pin connector |
Before Ordering
- Confirm MA002 and twelve positions.
- Identify the correct board and connection point.
- Inspect mating contacts and damaged conductors.
- Obtain approved termination and wiring requirements.
Package Contents and Separate Requirements
This offer identifies the removable connector. Main board, complete wiring harness, enclosure, power supply and operator are separate unless expressly included. Confirm the current plug and any termination pieces. A drawing showing the connector attached to the controller does not mean the controller is included in this small electrical service order.
Safety Warnings — Read Before Installation or Service
- WARNING: Electrical service can expose hazardous voltage and moving equipment. Use qualified service personnel and electrical personnel where required.
- Disconnect every applicable mains, battery and auxiliary supply before work. Follow the equipment instructions for stored energy and safe isolation.
- Record terminal assignments and isolate every supply before connector work. Do not guess pinout or reuse damaged mating contacts to restore power.
- Restore covers and wiring protection, then complete the model-specific functional and safety checks before returning the installation to normal use.
Related Products and Important Differences
- CPS-U monitored photo eyes — separate protection devices for approved commercial-door controls; match the operator and environment.
- TDC12X1BMC MAXUM trolley operator — a complete-operator comparison, not evidence that this legacy service part fits MAXUM.
Frequently Asked Questions
Is a control board included?
No. The connector and board are separate.
Is MA002J the same part?
No. It is a separate four-pin reference.
Does twelve pins prove generic fit?
No. Keying, pitch, terminals and application must match.
Can it repair damaged board contacts?
No. Inspect the mating interface independently.
Need Help Confirming the Right Product?
Contact Garage-DoorParts.com before ordering. Send the full equipment model, readable part labels and photographs of the installed assembly. Include the dimensions, electrical configuration or accessory details relevant to your project so the listing can be checked against the actual installation.
Details
Need Help With Compatibility?
Not sure if this is the correct part for your garage door, operator, gate system, or application? Contact Us before ordering — we’re happy to help.
Garage-DoorParts.com carries a large selection of residential and commercial parts, and many components can look similar while having important differences in dimensions, model numbers, voltage, mounting, or compatibility.
For the best assistance, please provide as much information as possible, including the manufacturer, model number, part number, door or operator type, dimensions, and clear photos of the existing part or equipment.
Our goal is to help you identify the correct product before you order and reduce the possibility of ordering an incompatible part.
Contact Us with your product questions and compatibility information, and we’ll do our best to point you in the right direction.
Shipping & Returns
We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.
We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.