LiftMaster LMHS24R 24 VDC Red Horn / FIRE Strobe
The LiftMaster LMHS24R is the red horn-and-strobe notification accessory identified in the manufacturer fire-door release-device documentation. The accessory table describes a 24 VDC horn/strobe with FIRE marking and a 2W designation. Confirm the exact approved notification circuit and delivered appliance specification before purchase; it is separate from a speaker/strobe, a strobe-only appliance and the release controller itself. Select the replacement by the complete part number and the installed equipment configuration. A similar photograph or a shared LiftMaster brand name does not establish interchangeability. Confirm the applicable service drawing before ordering so the repair addresses the correct component and its related mounting, connection and operating requirements.
Compatibility — Models, Versions and Exclusions
| Model or selection point | Compatibility requirement |
|---|---|
| Approved release-device circuit | Confirm the exact manual and current appliance match. |
| Horn versus speaker | LMHS24R identifies a horn/strobe, not a speaker/strobe. |
| Power and supervision | Verify circuit capacity, polarity and supervision requirements. |
| Other notification systems | No universal fire-alarm or gate-control compatibility is established. |
Identify the Assembly and Plan the Repair
Select the appliance as part of the complete documented notification arrangement. The 24 VDC description alone does not establish circuit compatibility, available current or required synchronization. Have qualified fire-door or notification-system personnel confirm the actual controller, power source and current appliance specification. Do not infer candela, sound output, weather rating or mounting accessories from the short catalog title.
Manufacturer release-device documentation notes that some accessories require a separate power source. Confirm the applicable wiring, supervision and power requirements before installation rather than assume that every controller output can power the horn/strobe directly. After service, complete the required notification, release and supervision tests for the installed system. A visible flash or audible sound alone does not establish full system compliance or correct release operation.
An electrical symptom does not identify the failed component by itself. Have qualified service personnel inspect the supply, wiring, connections and equipment condition before replacing parts. Record existing labels and terminal references with power safely isolated. A replacement should restore the documented circuit arrangement; it should not be used to change operating voltage, defeat a protective function or compensate for a mechanical load that the equipment cannot safely move.
Specifications and Product Identification
| Specification | Details |
|---|---|
| Ordering reference | LMHS24R |
| Component | Horn / strobe notification accessory |
| Voltage designation | 24 VDC |
| Color / marking | Red / FIRE |
| Manufacturer accessory-table designation | 2W; confirm actual appliance electrical data |
| System role | Notification appliance for an approved release-device arrangement |
Before Ordering
- Identify the exact release device and notification circuit.
- Confirm LMHS24R, 24 VDC and red FIRE marking.
- Verify current appliance ratings and power/supervision requirements.
- Plan notification, release and fault-supervision tests.
Package Contents and Separate Requirements
This offer identifies the horn/strobe accessory. Confirm current supplied appliance and mounting pieces. A release controller, external power supply, backbox, wiring, end-of-line device, smoke detector and complete fire-door system are not established as included. Obtain any separately required circuit and installation components from the approved system design.
Safety Warnings — Read Before Installation or Service
- WARNING: Fire-door notification and release-system service requires qualified personnel. Incorrect selection or wiring can prevent required warning or release operation.
- Isolate all applicable controller and auxiliary supplies using the approved service procedure before wiring or replacing the appliance.
- Do not bypass circuit supervision or required notification and release functions. Verify the actual appliance ratings and approved circuit capacity.
- Complete the prescribed notification, release and fault-supervision tests for the entire affected system before returning it to service.
Related Products and Important Differences
- CPS-U monitored photo eyes — separate protection devices for approved commercial-door controls; match the operator and environment.
- TDC12X1BMC MAXUM trolley operator — a complete-operator comparison, not evidence that this legacy service part fits MAXUM.
Frequently Asked Questions
Is it a speaker/strobe?
No. The manufacturer distinguishes the horn/strobe from the separate speaker/strobe accessory.
Can it connect to any 24 V circuit?
No. Confirm approved circuit type, capacity, polarity, supervision and actual appliance ratings.
Are candela and sound levels specified here?
No unverified output values are claimed. Use the current appliance documentation.
Is a flash test enough after installation?
No. Qualified personnel must complete the required notification, release and supervision checks for the complete system.
Need Help Confirming the Right Product?
Contact Garage-DoorParts.com before ordering. Send the full equipment model, readable part labels and photographs of the installed assembly. Include the dimensions, electrical configuration or accessory details relevant to your project so the listing can be checked against the actual installation.
Details
Need Help With Compatibility?
Not sure if this is the correct part for your garage door, operator, gate system, or application? Contact Us before ordering — we’re happy to help.
Garage-DoorParts.com carries a large selection of residential and commercial parts, and many components can look similar while having important differences in dimensions, model numbers, voltage, mounting, or compatibility.
For the best assistance, please provide as much information as possible, including the manufacturer, model number, part number, door or operator type, dimensions, and clear photos of the existing part or equipment.
Our goal is to help you identify the correct product before you order and reduce the possibility of ordering an incompatible part.
Contact Us with your product questions and compatibility information, and we’ll do our best to point you in the right direction.
Shipping & Returns
We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.
We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.