LiftMaster LMEHUL Extended Photo-Eye Hood — Sold Individually

LiftMaster LMEHUL Extended Photo-Eye Hood — Sold Individually

$56.42
Skip to product information
LiftMaster LMEHUL Extended Photo-Eye Hood — Sold Individually

LiftMaster LMEHUL Extended Photo-Eye Hood — Sold Individually

LMEHUL
$56.42
Shipping calculated at checkout.

The LiftMaster LMEHUL is the extended photo-eye hood accessory offered as a single item. It is a physical sensor accessory rather than a replacement photo eye, new wiring interface or a change to the operator’s safety logic. Match the exact sensor housing and current hood instructions before ordering. A hood may help shield the intended sensor position, but its presence does not establish a waterproof upgrade, a new sensing range or compatibility with every LiftMaster photo-eye model.

Compatibility — Models, Versions and Exclusions

Model or selection point Compatibility requirement
Photo eyes expressly specifying LMEHUL Match the sensor and current attachment arrangement.
Two-sensor installations Determine whether separate hoods are needed; this offer is single.
Intercom sun hoods Different products and geometry.
Other photo-eye housings No universal fit established.
Sensor misalignment or wiring faults Require diagnosis; a hood is not an electronic repair.

Check the Sensor and the Cause of Unstable Detection

Record the complete sensor model and photograph the housing, mounting and light exposure before choosing a hood. A symptom that appears at a certain time of day may involve the sensor location, reflection, alignment or another condition. Have the installer verify the actual cause rather than treating every intermittent beam fault as a need for more shade. Do not cover or obstruct the sensing aperture with improvised material.

Use the exact accessory attachment instructions and preserve the sensor’s alignment and required field of view. The hood must remain secure without contacting the moving gate or door, straining the wiring or collecting debris in the sensing path. After installation, test beam interruption and the required operator response under the applicable procedure. If the fault persists, continue the sensor and wiring diagnosis rather than bypassing protection to restore operation.

Specifications and Product Identification

Specification Details
Model LMEHUL
Product Extended photo-eye hood
Supplier quantity Single hood
Sensor electronics Separate
Selection basis Exact sensor housing and accessory instructions
Unverified capabilities No new range or environmental rating asserted

Before Ordering

  • Record the complete photo-eye model and housing revision.
  • Confirm LMEHUL is the specified hood.
  • Check mounting clearance and actual source of interference.
  • Order the required number of single hoods and plan full sensor tests.

Package Contents and Separate Requirements

This offer identifies one LMEHUL extended hood. A photo-eye pair, reflector, sensor brackets, wiring, operator and complete safety-device kit are not promised as included. Confirm any hood-specific fastening pieces with the current package. A system with two sensor housings does not change this listing into a two-hood carton. Determine the needed quantity and any separate damaged mounting components before scheduling service at the entrance.

Safety Warnings — Read Before Installation or Service

  • WARNING: Photo eyes are safety devices and must remain correctly positioned and functional. Use qualified service personnel for changes to their mounting.
  • Isolate applicable power before disturbing sensor wiring or working beside moving equipment. Keep the entrance clear during service.
  • Do not obstruct the sensing aperture, alter the housing or bypass a sensor to conceal a beam fault. Use only the documented hood arrangement.
  • Verify stable alignment, beam-interruption response and all required gate or door safety tests before normal operation.

Related Products and Important Differences

Frequently Asked Questions

Is a sensor included?

No. This is the hood accessory.

Is it sold as a pair?

The supplier identifies a single hood.

Does it make the sensor waterproof?

No additional environmental rating is established.

Will it fit every LiftMaster photo eye?

No. Confirm the exact housing and specified accessory.

Need Help Confirming the Right Product?

Contact Garage-DoorParts.com before ordering. Send the full equipment model, readable part labels and photographs of the installed assembly. Include the dimensions, electrical configuration or accessory details relevant to your project so the listing can be checked against the actual installation.

Details

Need Help With Compatibility?

Not sure if this is the correct part for your garage door, operator, gate system, or application? Contact Us before ordering — we’re happy to help.

Garage-DoorParts.com carries a large selection of residential and commercial parts, and many components can look similar while having important differences in dimensions, model numbers, voltage, mounting, or compatibility.

For the best assistance, please provide as much information as possible, including the manufacturer, model number, part number, door or operator type, dimensions, and clear photos of the existing part or equipment.

Our goal is to help you identify the correct product before you order and reduce the possibility of ordering an incompatible part.

Contact Us with your product questions and compatibility information, and we’ll do our best to point you in the right direction.

Shipping & Returns

We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.

We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.

Related products