LiftMaster K77-16011 CPS-N4 Photo-Eye Hardware Kit
The LiftMaster K77-16011 is the hardware-kit service reference identified in the manufacturer instructions for the documented CPS-N4, CPS3-N4 and CPS-LN4 photo-eye arrangements. It identifies mounting hardware rather than a replacement pair of photoelectric sensors. Match the exact sensor generation and installation drawing before ordering so that mechanical hardware is not confused with the emitter, receiver or interface components. Select the replacement by the complete part number and the installed equipment configuration. A similar photograph or a shared LiftMaster brand name does not establish interchangeability. Confirm the applicable service drawing before ordering so the repair addresses the correct component and its related mounting, connection and operating requirements.
Compatibility — Models, Versions and Exclusions
| Model or selection point | Compatibility requirement |
|---|---|
| Matching N4 photo-eye assembly | Verify the hardware callout and installation revision. |
| Emitter / receiver repair | Sensors have separate service references. |
| CPS-U and other generations | No universal mounting-kit fit is established. |
| Environmental suitability | Hardware alone does not confer an N4 equipment rating. |
Identify the Assembly and Plan the Repair
Inspect the actual mounting surfaces and cause of sensor misalignment before selecting a hardware kit. A damaged support, impact or loose attachment may need correction in addition to replacement hardware. Keep the sensor and interface callouts distinct when diagnosing an electrical fault; a mounting kit cannot restore a failed emitter or receiver circuit.
Use the manufacturer’s prescribed mounting position, support and alignment procedure for the exact photo-eye arrangement. Do not infer that a bracket can be relocated arbitrarily because the beam still appears to reach the opposite sensor. After repair, verify the required monitored protection behavior under the operator instructions. A beam that appears aligned is not by itself a complete safety-function test.
An electrical symptom does not identify the failed component by itself. Have qualified service personnel inspect the supply, wiring, connections and equipment condition before replacing parts. Record existing labels and terminal references with power safely isolated. A replacement should restore the documented circuit arrangement; it should not be used to change operating voltage, defeat a protective function or compensate for a mechanical load that the equipment cannot safely move.
Specifications and Product Identification
| Specification | Details |
|---|---|
| Ordering reference | K77-16011 |
| Component | Photo-eye hardware service kit |
| Documented arrangements | CPS-N4 / CPS3-N4 / CPS-LN4 |
| Separate emitter reference | 50-15514 |
| Separate receiver reference | 50-15515 |
| Separate interface components | 41K4629 / CPS3CARD as applicable to the documented arrangement |
Before Ordering
- Record the complete photo-eye and operator identification.
- Match the K77-16011 hardware callout.
- Inspect mounting supports and separate sensor condition.
- Plan prescribed alignment and monitored protection testing.
Package Contents and Separate Requirements
This offer identifies the photo-eye hardware kit. Emitters, receivers, interface electronics, complete sensor sets and operator controls are not established as included. Confirm the current supplied mounting pieces and quantity against the exact installation drawing before purchasing separate damaged sensor or interface components.
Safety Warnings — Read Before Installation or Service
- WARNING: Electrical service can expose hazardous voltage and moving equipment. Use qualified service personnel and electrical personnel where required.
- Disconnect every applicable mains, battery and auxiliary supply before work. Follow the equipment instructions for stored energy and safe isolation.
- Never bypass monitored photo-eye protection or substitute unapproved mounting. Follow the prescribed sensor position and complete the operator’s required obstruction-response tests.
- Restore covers and wiring protection, then complete the model-specific functional and safety checks before returning the installation to normal use.
Related Products and Important Differences
- CPS-U monitored photo eyes — separate protection devices for approved commercial-door controls; match the operator and environment.
- TDC12X1BMC MAXUM trolley operator — a complete-operator comparison, not evidence that this legacy service part fits MAXUM.
Frequently Asked Questions
Does it include a pair of photo eyes?
No sensor pair is established as included. The manufacturer lists separate emitter and receiver references.
Will it fix a failed receiver?
No. Diagnose the sensor circuit and select the approved receiver or other failed component separately.
Can it convert ordinary sensors to N4?
No environmental-rating conversion is established by mounting hardware.
Is visual alignment sufficient after service?
No. Complete the prescribed monitored protection and operator response tests for the actual system.
Need Help Confirming the Right Product?
Contact Garage-DoorParts.com before ordering. Send the full equipment model, readable part labels and photographs of the installed assembly. Include the dimensions, electrical configuration or accessory details relevant to your project so the listing can be checked against the actual installation.
Details
Need Help With Compatibility?
Not sure if this is the correct part for your garage door, operator, gate system, or application? Contact Us before ordering — we’re happy to help.
Garage-DoorParts.com carries a large selection of residential and commercial parts, and many components can look similar while having important differences in dimensions, model numbers, voltage, mounting, or compatibility.
For the best assistance, please provide as much information as possible, including the manufacturer, model number, part number, door or operator type, dimensions, and clear photos of the existing part or equipment.
Our goal is to help you identify the correct product before you order and reduce the possibility of ordering an incompatible part.
Contact Us with your product questions and compatibility information, and we’ll do our best to point you in the right direction.
Shipping & Returns
We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.
We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.