LiftMaster K41-0449-000 Barrier-Arm Mounting Hardware — TECHNA

LiftMaster K41-0449-000 Barrier-Arm Mounting Hardware — TECHNA

$28.56
Skip to product information
LiftMaster K41-0449-000 Barrier-Arm Mounting Hardware — TECHNA

LiftMaster K41-0449-000 Barrier-Arm Mounting Hardware — TECHNA

K41-0449-000
$28.56
Shipping calculated at checkout.

The LiftMaster K41-0449-000 is the barrier-arm mounting-hardware service reference identified in TECHNA repair information. It supplies the specified attachment hardware role and is separate from the arm bracket, arm-retention kit, shaft cover and spring module. Match the exact barrier model and arm arrangement before ordering so the hardware restores the intended attachment without assuming every arm-related part is included. Select the replacement by the complete part number and the installed equipment configuration. A similar photograph or a shared LiftMaster brand name does not establish interchangeability. Confirm the applicable service drawing before ordering so the repair addresses the correct component and its related mounting, connection and operating requirements.

Compatibility — Models, Versions and Exclusions

Model or selection point Compatibility requirement
TECHNA drawing specifying this reference Match the model and arm configuration.
Arm bracket assembly Separate service item; do not infer inclusion.
Arm-retention kit Separate reference and repair scope.
Legacy Mega Arm hardware No universal interchangeability with TECHNA hardware established.

Identify the Assembly and Plan the Repair

Inspect the arm, bracket and shaft connection after an impact or loose-hardware complaint. Replacement fasteners cannot restore a bent bracket, damaged thread or worn interface. Identify which parts require service before choosing a hardware-only order.

Barrier arms can move unexpectedly and may be acted on by balancing components. Follow the exact operator procedure for supporting the arm and securing the mechanism during service. Use the specified fasteners and retention requirements; do not guess dimensions, substitute ordinary hardware or change the arm arrangement to approximate a fit.

Compare the replacement with the installed service arrangement before dismantling the equipment. Photograph the part’s location and record the complete model and visible service numbers. Inspect the surrounding attachment points and mating components for wear, impact damage or misalignment. Replacing one worn item will not correct a damaged support or another component that continues to impose abnormal loads on the repaired assembly.

Plan the repair around the manufacturer’s instructions for the actual equipment revision. Confirm access, safe support and any separate hardware before removing the old part. After installation, restore the intended retention, alignment and guarding, then test the equipment under controlled conditions. The repair is complete only when the original fault has been addressed and the system’s required operating and protection functions have been checked.

Specifications and Product Identification

Specification Details
Ordering reference K41-0449-000
Product Arm mounting hardware
Platform Documented TECHNA barrier arrangement
Separate arm bracket K41-0440-000 where specified
Separate retention kit K41-0442-000

Before Ordering

  • Confirm the complete TECHNA model.
  • Locate K41-0449-000 in the repair drawing.
  • Inspect arm, bracket, threads and shaft connection.
  • Verify current hardware inventory and installation requirements.

Package Contents and Separate Requirements

This offer identifies the arm-mounting hardware. The barrier arm, bracket assembly, separate retention kit, spring module, motor and operator are not promised as included. Confirm the supplied fastener inventory before disassembly. Neighboring arm components shown in the repair diagram describe the system and are not automatically bundled.

Safety Warnings — Read Before Installation or Service

  • WARNING: A moving gate and exposed barrier-arm mounting hardware — techna can cause serious injury. Installation and service require a qualified gate-systems technician.
  • Isolate AC power, batteries and any solar supply as applicable, and secure the gate against unexpected movement before work begins.
  • Support and secure the barrier arm and stored balancing loads before loosening its attachment. Use the exact fastener and retention procedure; do not substitute ordinary hardware.
  • Restore all covers and guards, then verify travel endpoints, reversal and every required safety device before returning the gate to normal operation.

Related Products and Important Differences

  • LMRRUL monitored photo eye — a separate protection option only where the exact operator and control revision approve it; not a universal legacy retrofit.
  • LMWEKITU monitored wireless edge kit — a separate edge communication system for approved controls and resistive edges; not a replacement for this mechanical or electrical service part.

Frequently Asked Questions

Is the bracket included?

The bracket is separately identified; no combined package is promised.

Is it the arm-retention kit?

No. K41-0442-000 is a separate reference.

Will it fix a bent shaft connection?

No. Mating damage requires separate repair.

Can ordinary fasteners be substituted?

Use the documented hardware and exact installation requirements.

Need Help Confirming the Right Product?

Contact Garage-DoorParts.com before ordering. Send the full equipment model, readable part labels and photographs of the installed assembly. Include the dimensions, electrical configuration or accessory details relevant to your project so the listing can be checked against the actual installation.

Details

Need Help With Compatibility?

Not sure if this is the correct part for your garage door, operator, gate system, or application? Contact Us before ordering — we’re happy to help.

Garage-DoorParts.com carries a large selection of residential and commercial parts, and many components can look similar while having important differences in dimensions, model numbers, voltage, mounting, or compatibility.

For the best assistance, please provide as much information as possible, including the manufacturer, model number, part number, door or operator type, dimensions, and clear photos of the existing part or equipment.

Our goal is to help you identify the correct product before you order and reduce the possibility of ordering an incompatible part.

Contact Us with your product questions and compatibility information, and we’ll do our best to point you in the right direction.

Shipping & Returns

We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.

We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.

Related products