LiftMaster K180A0385-3 Latch Cover and Three-Phase Switch — SL585UL Service Assembly
The LiftMaster K180A0385-3 is the latch-cover and three-phase switch service reference shown in documented SL585UL electrical-box arrangements. Manufacturer diagrams also call it the lockout bracket and three-phase switch. It is distinct from K75-38037 for the single-phase arrangement and must match the installed enclosure, mechanism and circuit. The supplier’s shortened SL585 label should be checked against the complete operator suffix before ordering. Select the replacement by the complete part number and the installed equipment configuration. A similar photograph or a shared LiftMaster brand name does not establish interchangeability. Confirm the applicable service drawing before ordering so the repair addresses the correct component and its related mounting, connection and operating requirements.
Compatibility — Models, Versions and Exclusions
| Model or selection point | Compatibility requirement |
|---|---|
| SL585UL three-phase drawing | Match the complete model and electrical box. |
| Single-phase versions | Separate K75-38037 arrangement; do not substitute by appearance. |
| SL595UL | Its manufacturer diagram also identifies this reference; confirm exact revision. |
| Complete control enclosure | Separate service scope, not included with the latch/switch item. |
Identify the Assembly and Plan the Repair
Inspect the latch engagement, switch connection and mounting support before deciding what to replace. A cover that does not engage can be distorted or incorrectly positioned, while a control complaint may involve wiring rather than the switch itself. Record the equipment label and actual mechanism, then match both to the appropriate three-phase diagram.
Restore the documented actuation and wire clearance without forcing a bent cover or bridging the switch to suppress a fault. A replacement switch cannot repair a damaged electrical enclosure. Verify engagement and the associated control response after assembly, then complete normal gate travel and required protection-device tests.
An electrical symptom does not identify the failed component by itself. Have qualified service personnel inspect the supply, wiring, connections and equipment condition before replacing parts. Record existing labels and terminal references with power safely isolated. A replacement should restore the documented circuit arrangement; it should not be used to change operating voltage, defeat a protective function or compensate for a mechanical load that the equipment cannot safely move.
Compare the delivered item with the approved service reference before installation. The installer must obtain the equipment-specific wiring, mounting and commissioning instructions rather than infer them from the appearance of the part. Keep conductors clear of moving components and reinstall the intended covers. After the repair, check the original complaint and the equipment’s required operating and safety functions; a successful power-up alone is not a complete service test.
Specifications and Product Identification
| Specification | Details |
|---|---|
| Ordering reference | K180A0385-3 |
| Function | Latch cover / lockout bracket with switch |
| Electrical designation | Three phase / 3PH |
| Documented example | SL585UL; exact revision must match |
| Separate 1PH reference | K75-38037 |
Before Ordering
- Record the full operator model and phase.
- Match the three-phase service reference.
- Inspect latch, bracket, cover and switch wiring.
- Confirm the current package and required control-response tests.
Package Contents and Separate Requirements
The listing identifies the latch-cover/lockout-bracket and three-phase switch service assembly. Confirm its mounting and connection pieces in the current carton. A full electrical box, power board, main control board, complete harness and gate operator are separate. The surrounding items shown in the diagram do not become part of this smaller assembly order.
Safety Warnings — Read Before Installation or Service
- WARNING: Electrical service can expose hazardous voltage and moving equipment. Use qualified service personnel and electrical personnel where required.
- Disconnect every applicable mains, battery and auxiliary supply before work. Follow the equipment instructions for stored energy and safe isolation.
- Do not bridge the latch switch or force a distorted cover to make it actuate. Restore the exact three-phase arrangement and verify its intended control response.
- Restore covers and wiring protection, then complete the model-specific functional and safety checks before returning the installation to normal use.
Related Products and Important Differences
- CPS-U monitored photo eyes — separate protection devices for approved commercial-door controls; match the operator and environment.
- TDC12X1BMC MAXUM trolley operator — a complete-operator comparison, not evidence that this legacy service part fits MAXUM.
Frequently Asked Questions
Is it the single-phase version?
No. K75-38037 is separately identified for that arrangement.
Is it just an outer operator cover?
No. It is the documented latch/lockout bracket and switch service assembly.
Can the switch be bridged temporarily?
Do not defeat the intended control arrangement; diagnose and repair the fault.
Does it repair a bent control box?
No. Structural and wiring damage need separate assessment.
Need Help Confirming the Right Product?
Contact Garage-DoorParts.com before ordering. Send the full equipment model, readable part labels and photographs of the installed assembly. Include the dimensions, electrical configuration or accessory details relevant to your project so the listing can be checked against the actual installation.
Details
Need Help With Compatibility?
Not sure if this is the correct part for your garage door, operator, gate system, or application? Contact Us before ordering — we’re happy to help.
Garage-DoorParts.com carries a large selection of residential and commercial parts, and many components can look similar while having important differences in dimensions, model numbers, voltage, mounting, or compatibility.
For the best assistance, please provide as much information as possible, including the manufacturer, model number, part number, door or operator type, dimensions, and clear photos of the existing part or equipment.
Our goal is to help you identify the correct product before you order and reduce the possibility of ordering an incompatible part.
Contact Us with your product questions and compatibility information, and we’ll do our best to point you in the right direction.
Shipping & Returns
We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.
We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.