LiftMaster K17-10336 Commercial V-Belt Pulley — 7-Inch OD, 3/4-Inch Bore, 4L Profile

LiftMaster K17-10336 Commercial V-Belt Pulley — 7-Inch OD, 3/4-Inch Bore, 4L Profile

$31.32
Skip to product information
LiftMaster K17-10336 Commercial V-Belt Pulley — 7-Inch OD, 3/4-Inch Bore, 4L Profile

LiftMaster K17-10336 Commercial V-Belt Pulley — 7-Inch OD, 3/4-Inch Bore, 4L Profile

K17-10336
$31.32
Shipping calculated at checkout.

The LiftMaster K17-10336 is a commercial-operator pulley identified by a 7-inch outside diameter, 3/4-inch bore and 4L belt profile. The 4L designation describes the belt section, not a four-inch belt length. Match the pulley, shaft and approved belt-drive arrangement before selecting this mechanical service component for the installed operator. Select the replacement by the complete part number and the installed equipment configuration. A similar photograph or a shared LiftMaster brand name does not establish interchangeability. Confirm the applicable service drawing before ordering so the repair addresses the correct component and its related mounting, connection and operating requirements.

Compatibility — Models, Versions and Exclusions

Model or selection point Compatibility requirement
Matching commercial drive Confirm the exact pulley reference in the operator parts diagram.
Shaft fit Verify the 3/4-inch bore and actual retention arrangement.
Belt selection Match the documented 4L profile and separately specified belt length.
Drive geometry Check pulley position, mating pulley alignment and guard clearance.

Identify the Assembly and Plan the Repair

The pulley must suit the complete belt drive, including the motor or driven shaft, mating pulley and available adjustment range. Do not infer speed ratio from the outside diameter alone or substitute a different pulley to overcome a door that binds. The approved pulley and belt combination should restore the original documented drive arrangement.

Inspect the belt, shaft and surrounding supports for wear or misalignment. A damaged belt or loose shaft attachment can continue to cause slipping after a pulley is replaced. Obtain any missing hub, keying or groove dimensions from the current service drawing rather than guessing from a photograph, and retain the original belt guarding and safe service access.

Compare the replacement with the installed service arrangement before dismantling the equipment. Photograph the part’s location and record the complete model and visible service numbers. Inspect the surrounding attachment points and mating components for wear, impact damage or misalignment. Replacing one worn item will not correct a damaged support or another component that continues to impose abnormal loads on the repaired assembly.

Specifications and Product Identification

Specification Details
Ordering reference K17-10336
Outside diameter 7 inches
Bore 3/4 inch
Belt designation 4L profile
Component V-belt pulley; belt length not specified by 4L

Before Ordering

  • Confirm the exact part number in the commercial operator diagram.
  • Verify 7-inch OD, 3/4-inch bore and 4L belt profile.
  • Identify belt length separately from its profile designation.
  • Check retention, alignment, adjustment and guard clearances.

Package Contents and Separate Requirements

This offer identifies the pulley service reference. A V-belt, shaft key, separate retention hardware, motor and complete drive assembly are not established as included. Confirm the current package and obtain the exact belt and attachment parts required by the equipment-specific service instructions.

Safety Warnings — Read Before Installation or Service

  • WARNING: A moving commercial door and exposed commercial v-belt pulley — 7-inch od, 3/4-inch bore, 4l profile can cause serious injury or death. Have a trained door-systems technician perform installation and service.
  • Disconnect mains power and any battery backup before mechanical work or wiring. Secure the door against unexpected movement as directed by its manufacturer.
  • Do not work on springs, cables or counterbalance components without appropriate training. Never bypass safety sensors or increase force to overcome binding.
  • Restore guards and complete the model-specific travel, reversal and protection-device tests before returning the door to normal operation.

Related Products and Important Differences

Frequently Asked Questions

Does 4L mean a four-inch belt?

No. It is a belt-profile designation. Belt length must be selected separately from the approved parts information.

Is a belt supplied?

Do not assume that a belt is included with this pulley reference. Check current contents before ordering other drive parts.

Will a matching bore guarantee fit?

No. Pulley diameter, belt profile, hub arrangement, retention and alignment must also match the documented application.

Can a new pulley fix a damaged belt?

No. Inspect the complete belt drive and replace or correct other worn components as required by the service procedure.

Need Help Confirming the Right Product?

Contact Garage-DoorParts.com before ordering. Send the full equipment model, readable part labels and photographs of the installed assembly. Include the dimensions, electrical configuration or accessory details relevant to your project so the listing can be checked against the actual installation.

Details

Need Help With Compatibility?

Not sure if this is the correct part for your garage door, operator, gate system, or application? Contact Us before ordering — we’re happy to help.

Garage-DoorParts.com carries a large selection of residential and commercial parts, and many components can look similar while having important differences in dimensions, model numbers, voltage, mounting, or compatibility.

For the best assistance, please provide as much information as possible, including the manufacturer, model number, part number, door or operator type, dimensions, and clear photos of the existing part or equipment.

Our goal is to help you identify the correct product before you order and reduce the possibility of ordering an incompatible part.

Contact Us with your product questions and compatibility information, and we’ll do our best to point you in the right direction.

Shipping & Returns

We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.

We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.

Related products