LiftMaster K12-10882 Replacement Bushing — 3/4 × 1 × 5/8 Inch
The LiftMaster K12-10882 is the replacement bushing identified with a 3/4 × 1 × 5/8-inch dimensional description in manufacturer commercial-operator parts information. It appears in the documented MH assembly and must be matched to the correct shaft and supporting location. It is distinct from the nearby nylon bearing and from a complete shaft or clutch service kit. Select the replacement by the complete part number and the installed equipment configuration. A similar photograph or a shared LiftMaster brand name does not establish interchangeability. Confirm the applicable service drawing before ordering so the repair addresses the correct component and its related mounting, connection and operating requirements.
Compatibility — Models, Versions and Exclusions
| Model or selection point | Compatibility requirement |
|---|---|
| MH drawing specifying K12-10882 | Locate the exact bushing position and revision. |
| Other commercial models | Verify their individual service drawings. |
| K12-10883 | Separate component; not an alternative number for this bushing. |
| Worn shaft or housing | A bushing-only replacement does not repair mating damage. |
Identify the Assembly and Plan the Repair
Confirm the full dimensional callout and the part’s location before ordering. Similar bushings elsewhere in an operator can differ in length, shoulder geometry or intended function. The dimensions do not establish universal fit in every shaft assembly with an approximately similar opening.
Inspect the mating shaft and support for wear, movement or distortion. A replacement bushing cannot restore a damaged shaft surface or a housing that no longer supports the assembly correctly. Use the exact operator service procedure for removal, positioning and any lubrication requirement rather than assuming a generic press-fit or bearing-maintenance method.
Compare the replacement with the installed service arrangement before dismantling the equipment. Photograph the part’s location and record the complete model and visible service numbers. Inspect the surrounding attachment points and mating components for wear, impact damage or misalignment. Replacing one worn item will not correct a damaged support or another component that continues to impose abnormal loads on the repaired assembly.
Plan the repair around the manufacturer’s instructions for the actual equipment revision. Confirm access, safe support and any separate hardware before removing the old part. After installation, restore the intended retention, alignment and guarding, then test the equipment under controlled conditions. The repair is complete only when the original fault has been addressed and the system’s required operating and protection functions have been checked.
Specifications and Product Identification
| Specification | Details |
|---|---|
| Ordering reference | K12-10882 |
| Manufacturer dimensions | 3/4 ×1 ×5/8 inch |
| Component | Bushing |
| Documented example | MH commercial hoist assembly |
| Separate neighboring reference | K12-10883 nylon bearing |
Before Ordering
- Match the complete K12-10882 reference.
- Verify the three listed dimensions.
- Identify its position in the exact assembly.
- Inspect the shaft, support and separate retention pieces.
Package Contents and Separate Requirements
This offer identifies the bushing. Shaft, clutch components, nylon bearing, pulley, support bracket and complete operator are separate. Confirm the supplied quantity and any accompanying pieces with the current carton. An exploded drawing showing the bushing within a shaft kit does not establish that the surrounding kit is included in this individual service order.
Safety Warnings — Read Before Installation or Service
- WARNING: A moving commercial door and exposed replacement bushing — 3/4 × 1 × 5/8 inch can cause serious injury or death. Have a trained door-systems technician perform installation and service.
- Disconnect mains power and any battery backup before mechanical work or wiring. Secure the door against unexpected movement as directed by its manufacturer.
- Do not work on springs, cables or counterbalance components without appropriate training. Never bypass safety sensors or increase force to overcome binding.
- Restore guards and complete the model-specific travel, reversal and protection-device tests before returning the door to normal operation.
Related Products and Important Differences
- CPS-U monitored photo eyes — separate protection devices for approved commercial-door controls; match the operator and environment.
- TDC12X1BMC MAXUM trolley operator — a complete-operator comparison, not evidence that this legacy service part fits MAXUM.
Frequently Asked Questions
Is it the nylon bearing K12-10883?
No. The manufacturer identifies that as a separate component.
Do the dimensions prove universal fit?
No. Match the exact service location and geometry.
Is a shaft included?
No shaft is promised with the bushing.
Can it correct a worn housing?
No. The mating support must be evaluated separately.
Need Help Confirming the Right Product?
Contact Garage-DoorParts.com before ordering. Send the full equipment model, readable part labels and photographs of the installed assembly. Include the dimensions, electrical configuration or accessory details relevant to your project so the listing can be checked against the actual installation.
Details
Need Help With Compatibility?
Not sure if this is the correct part for your garage door, operator, gate system, or application? Contact Us before ordering — we’re happy to help.
Garage-DoorParts.com carries a large selection of residential and commercial parts, and many components can look similar while having important differences in dimensions, model numbers, voltage, mounting, or compatibility.
For the best assistance, please provide as much information as possible, including the manufacturer, model number, part number, door or operator type, dimensions, and clear photos of the existing part or equipment.
Our goal is to help you identify the correct product before you order and reduce the possibility of ordering an incompatible part.
Contact Us with your product questions and compatibility information, and we’ll do our best to point you in the right direction.
Shipping & Returns
We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.
We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.