LiftMaster G02102 Two-Button Indoor Surface-Mount Control Station — Constant-Pressure Application

LiftMaster G02102 Two-Button Indoor Surface-Mount Control Station — Constant-Pressure Application

$42.26
Skip to product information
LiftMaster G02102 Two-Button Indoor Surface-Mount Control Station — Constant-Pressure Application

LiftMaster G02102 Two-Button Indoor Surface-Mount Control Station — Constant-Pressure Application

G02102
$42.26
Shipping calculated at checkout.

The LiftMaster G02102 is the supplier ordering reference for the two-button, indoor surface-mount control station. The documented application uses OPEN and CLOSE commands with an operator wired for constant pressure in both directions, corresponding to the stated D1 control arrangement. It is not a complete three-button station and should not be selected as a universal momentary-command replacement without checking the operator wiring. Select the replacement by the complete part number and the installed equipment configuration. A similar photograph or a shared LiftMaster brand name does not establish interchangeability. Confirm the applicable service drawing before ordering so the repair addresses the correct component and its related mounting, connection and operating requirements.

Compatibility — Models, Versions and Exclusions

Model or selection point Compatibility requirement
D1 constant-pressure control Verify the operator’s approved wiring and station requirements.
Momentary-command circuits No automatic substitution established.
Outdoor or wet locations The cited offer is for interior use.
Three-button STOP stations Different command set and control arrangement.

Identify the Assembly and Plan the Repair

Identify the intended operator control mode before ordering the station. Two visible buttons do not establish whether a system uses constant-pressure or momentary commands, nor do they determine all required stop and interlock functions. Have the installer confirm the circuit and station placement using the exact operator instructions.

Locate controls where the user can observe the door and remain clear of its moving parts, following the manufacturer installation requirements. The station does not replace protection devices or authorize defeating monitored inputs. If the existing installation requires a separate stop function or other controls, preserve that arrangement rather than assuming two buttons cover every requirement.

An electrical symptom does not identify the failed component by itself. Have qualified service personnel inspect the supply, wiring, connections and equipment condition before replacing parts. Record existing labels and terminal references with power safely isolated. A replacement should restore the documented circuit arrangement; it should not be used to change operating voltage, defeat a protective function or compensate for a mechanical load that the equipment cannot safely move.

Compare the delivered item with the approved service reference before installation. The installer must obtain the equipment-specific wiring, mounting and commissioning instructions rather than infer them from the appearance of the part. Keep conductors clear of moving components and reinstall the intended covers. After the repair, check the original complaint and the equipment’s required operating and safety functions; a successful power-up alone is not a complete service test.

Specifications and Product Identification

Specification Details
Ordering reference G02102
Buttons Two: OPEN and CLOSE
Mounting Surface mount
Location Interior use only
Control requirement Approved constant-pressure open/close arrangement

Before Ordering

  • Confirm the full G02102 station offer.
  • Verify indoor surface mounting.
  • Match the constant-pressure control arrangement.
  • Review visibility, wiring and all required stop/interlock functions.

Package Contents and Separate Requirements

The listing identifies the two-button station. Operator, external safety sensors, field wiring, conduit and any separate stop station are separate unless expressly bundled. Confirm the current enclosure and mounting hardware with the supplier. A station-only order does not provide a complete operator control conversion or establish compatibility with every commercial control circuit.

Safety Warnings — Read Before Installation or Service

  • WARNING: Electrical service can expose hazardous voltage and moving equipment. Use qualified service personnel and electrical personnel where required.
  • Disconnect every applicable mains, battery and auxiliary supply before work. Follow the equipment instructions for stored energy and safe isolation.
  • This two-button station does not provide a separate STOP button. Do not use it to remove required stopping or interlock functions; match the approved constant-pressure wiring.
  • Restore covers and wiring protection, then complete the model-specific functional and safety checks before returning the installation to normal use.

Related Products and Important Differences

Frequently Asked Questions

Is it for outdoor use?

The documented offer is for interior use only.

Does it provide a separate STOP button?

It is a two-button OPEN/CLOSE station; review the complete required control arrangement.

Can I assume momentary operation?

No. The stated application requires constant pressure in both directions.

Does it replace safety sensors?

No. Required protection remains part of the operator system.

Need Help Confirming the Right Product?

Contact Garage-DoorParts.com before ordering. Send the full equipment model, readable part labels and photographs of the installed assembly. Include the dimensions, electrical configuration or accessory details relevant to your project so the listing can be checked against the actual installation.

Details

Need Help With Compatibility?

Not sure if this is the correct part for your garage door, operator, gate system, or application? Contact Us before ordering — we’re happy to help.

Garage-DoorParts.com carries a large selection of residential and commercial parts, and many components can look similar while having important differences in dimensions, model numbers, voltage, mounting, or compatibility.

For the best assistance, please provide as much information as possible, including the manufacturer, model number, part number, door or operator type, dimensions, and clear photos of the existing part or equipment.

Our goal is to help you identify the correct product before you order and reduce the possibility of ordering an incompatible part.

Contact Us with your product questions and compatibility information, and we’ll do our best to point you in the right direction.

Shipping & Returns

We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.

We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.

Related products