LiftMaster AH103 Four-Inch Wheel Mounting Bracket — Unfinished Steel, Single
The LiftMaster AH103 is the single mounting bracket identified in the manufacturer gate-hardware catalog for a 4-inch wheel arrangement. It is made from unfinished steel and provides the specified wheel-support mounting component. The wheel, axle arrangement, gate frame and track must be selected and evaluated separately. A bracket-only purchase does not establish the capacity or suitability of a complete sliding-gate installation. Select the replacement by the complete part number and the installed equipment configuration. A similar photograph or a shared LiftMaster brand name does not establish interchangeability. Confirm the applicable service drawing before ordering so the repair addresses the correct component and its related mounting, connection and operating requirements.
Compatibility — Models, Versions and Exclusions
| Model or selection point | Compatibility requirement |
|---|---|
| Specified4-inch wheel arrangement | Verify wheel, axle and mounting geometry. |
| Other wheel diameters | No universal compatibility established. |
| Gate frame and attachment | Have a qualified installer evaluate structural suitability. |
| Track and guide system | Separate components; bracket selection does not establish their alignment or capacity. |
Identify the Assembly and Plan the Repair
Identify the complete wheel-support arrangement before fabrication or repair. Confirm the wheel and axle interface, mounting clearance and attachment to the gate frame. The4-inch designation describes the intended wheel arrangement; it does not provide all bracket dimensions or authorize pairing the bracket with every wheel of that nominal diameter.
Unfinished steel requires an appropriate finishing and maintenance plan for the completed installation. Inspect the supporting frame and track if the old bracket has bent or cracked. A new bracket cannot correct a distorted gate, unsuitable load distribution or a damaged running surface. The entire gate must remain safely supported while wheel hardware is being serviced.
Compare the replacement with the installed service arrangement before dismantling the equipment. Photograph the part’s location and record the complete model and visible service numbers. Inspect the surrounding attachment points and mating components for wear, impact damage or misalignment. Replacing one worn item will not correct a damaged support or another component that continues to impose abnormal loads on the repaired assembly.
Plan the repair around the manufacturer’s instructions for the actual equipment revision. Confirm access, safe support and any separate hardware before removing the old part. After installation, restore the intended retention, alignment and guarding, then test the equipment under controlled conditions. The repair is complete only when the original fault has been addressed and the system’s required operating and protection functions have been checked.
Specifications and Product Identification
| Specification | Details |
|---|---|
| Ordering reference | AH103 |
| Catalog description | 4-inch single bracket |
| Quantity per box | One |
| Material | Steel |
| Finish | Unfinished |
Before Ordering
- Confirm AH103 and the 4-inch wheel arrangement.
- Verify axle, wheel and bracket geometry.
- Inspect frame, attachment and track condition.
- Plan safe gate support and final finishing.
Package Contents and Separate Requirements
The manufacturer catalog identifies one unfinished-steel bracket. Wheel, axle, bearings, track, gate frame, installation fasteners and finishing materials are separate unless expressly included in the supplier offer. Confirm the current package before ordering. A photograph of a wheel mounted in a bracket is not evidence that the wheel assembly is supplied.
Safety Warnings — Read Before Installation or Service
- WARNING: A moving gate and exposed four-inch wheel mounting bracket — unfinished steel, single can cause serious injury. Installation and service require a qualified gate-systems technician.
- Support and secure the gate against falling or rolling before removing wheel hardware. Do not rely on the operator or a remaining wheel as the sole support.
- Keep people clear of the gate and drive during supervised testing. Never bypass required entrapment-protection devices or increase force to overcome a mechanical fault.
- Restore all covers and guards, then verify travel endpoints, reversal and every required safety device before returning the gate to normal operation.
Related Products and Important Differences
- LMRRUL monitored photo eye — a separate protection option only where the exact operator and control revision approve it; not a universal legacy retrofit.
- LMWEKITU monitored wireless edge kit — a separate edge communication system for approved controls and resistive edges; not a replacement for this mechanical or electrical service part.
Frequently Asked Questions
How many brackets are supplied?
The manufacturer catalog specifies one per box.
Is the wheel included?
No wheel is established as included with the bracket.
Is it painted or plated?
The catalog describes unfinished steel.
Does it establish the whole gate’s weight rating?
No. Evaluate the complete wheel, frame, track and support arrangement.
Need Help Confirming the Right Product?
Contact Garage-DoorParts.com before ordering. Send the full equipment model, readable part labels and photographs of the installed assembly. Include the dimensions, electrical configuration or accessory details relevant to your project so the listing can be checked against the actual installation.
Details
Need Help With Compatibility?
Not sure if this is the correct part for your garage door, operator, gate system, or application? Contact Us before ordering — we’re happy to help.
Garage-DoorParts.com carries a large selection of residential and commercial parts, and many components can look similar while having important differences in dimensions, model numbers, voltage, mounting, or compatibility.
For the best assistance, please provide as much information as possible, including the manufacturer, model number, part number, door or operator type, dimensions, and clear photos of the existing part or equipment.
Our goal is to help you identify the correct product before you order and reduce the possibility of ordering an incompatible part.
Contact Us with your product questions and compatibility information, and we’ll do our best to point you in the right direction.
Shipping & Returns
We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.
We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.