LiftMaster 80-207-35 Mechanical Shaft Key — 1/4 × 1/4 × 1 Inch
The LiftMaster 80-207-35 is a mechanical shaft key measuring 1/4 inch by 1/4 inch by 1 inch, identified in the documented SW420 drive parts. It engages matching shaft and hub keyways to transmit rotation in the specified assembly. This is a metal drive component, not a lock key, release key or access-control credential. Select the replacement by the complete part number and the installed equipment configuration. A similar photograph or a shared LiftMaster brand name does not establish interchangeability. Confirm the applicable service drawing before ordering so the repair addresses the correct component and its related mounting, connection and operating requirements.
Compatibility — Models, Versions and Exclusions
| Model or selection point | Compatibility requirement |
|---|---|
| SW420 documented assembly | Confirm the exact position and service reference. |
| Other keyed drives | All dimensions and the approved service arrangement must match. |
| Damaged shaft keyways | A replacement key does not repair worn shaft engagement. |
| Lock or release mechanisms | Not a lock-cylinder or release-access key. |
Identify the Assembly and Plan the Repair
Measure the required cross section and length and identify the mating hub and shaft. A key that is too short, loose or improperly seated can leave the drive connection unsuitable even if the hub can be pushed onto the shaft. Do not file an unrelated key or stack improvised material to approximate the specified fit.
Inspect the shaft and hub keyways for deformation and movement-related damage. A sheared key may be the result of a drive fault rather than an isolated defect. Have the technician evaluate alignment, retention and abnormal loading before replacement. Follow the exact assembly instructions for the key and associated fastening arrangement.
Compare the replacement with the installed service arrangement before dismantling the equipment. Photograph the part’s location and record the complete model and visible service numbers. Inspect the surrounding attachment points and mating components for wear, impact damage or misalignment. Replacing one worn item will not correct a damaged support or another component that continues to impose abnormal loads on the repaired assembly.
Plan the repair around the manufacturer’s instructions for the actual equipment revision. Confirm access, safe support and any separate hardware before removing the old part. After installation, restore the intended retention, alignment and guarding, then test the equipment under controlled conditions. The repair is complete only when the original fault has been addressed and the system’s required operating and protection functions have been checked.
Specifications and Product Identification
| Specification | Details |
|---|---|
| Ordering reference | 80-207-35 |
| Cross section | 1/4 × 1/4 inch |
| Length | 1 inch |
| Documented example | SW420 drive parts |
| Function | Keyed shaft-to-hub engagement |
Before Ordering
- Confirm all three key dimensions.
- Locate the correct shaft/hub connection.
- Inspect both mating keyways and retention.
- Diagnose the cause of a sheared or displaced key.
Package Contents and Separate Requirements
The listing identifies the shaft key. A shaft, sprocket, pulley, hub, set screws and complete drive assembly are separate unless expressly supplied. Confirm the order quantity with the supplier; the dimensional description specifies one key’s size rather than a kit of multiple drive components.
Safety Warnings — Read Before Installation or Service
- WARNING: A moving gate and exposed mechanical shaft key — 1/4 × 1/4 × 1 inch can cause serious injury. Installation and service require a qualified gate-systems technician.
- Isolate AC power, batteries and any solar supply as applicable, and secure the gate against unexpected movement before work begins.
- Keep people clear of the gate and drive during supervised testing. Never bypass required entrapment-protection devices or increase force to overcome a mechanical fault.
- Restore all covers and guards, then verify travel endpoints, reversal and every required safety device before returning the gate to normal operation.
Related Products and Important Differences
- LMRRUL monitored photo eye — a separate protection option only where the exact operator and control revision approve it; not a universal legacy retrofit.
- LMWEKITU monitored wireless edge kit — a separate edge communication system for approved controls and resistive edges; not a replacement for this mechanical or electrical service part.
Frequently Asked Questions
Is it a gate lock key?
No. It is a mechanical key for a shaft and hub.
What does the one-inch dimension describe?
The key length; the cross section is 1/4 by 1/4 inch.
Can it repair a worn keyway?
No. The shaft and hub require their own assessment.
Can I shorten a different key instead?
Use the specified replacement and approved assembly requirements rather than improvising fit.
Need Help Confirming the Right Product?
Contact Garage-DoorParts.com before ordering. Send the full equipment model, readable part labels and photographs of the installed assembly. Include the dimensions, electrical configuration or accessory details relevant to your project so the listing can be checked against the actual installation.
Details
Need Help With Compatibility?
Not sure if this is the correct part for your garage door, operator, gate system, or application? Contact Us before ordering — we’re happy to help.
Garage-DoorParts.com carries a large selection of residential and commercial parts, and many components can look similar while having important differences in dimensions, model numbers, voltage, mounting, or compatibility.
For the best assistance, please provide as much information as possible, including the manufacturer, model number, part number, door or operator type, dimensions, and clear photos of the existing part or equipment.
Our goal is to help you identify the correct product before you order and reduce the possibility of ordering an incompatible part.
Contact Us with your product questions and compatibility information, and we’ll do our best to point you in the right direction.
Shipping & Returns
We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.
We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.