LiftMaster 2180SS Stainless Steel Specialty Gate Hinges — Flat Both Sides, Pair
The LiftMaster 2180SS is the stainless steel specialty gate-hinge pair with flat mounting surfaces on both sides. The manufacturer identifies a 1,000 lb capacity per pair for this hinge selection, subject to a properly designed and supported gate installation. Select it by mounting geometry, gate requirements and structural support rather than treating a weight figure as the only installation criterion. Select the replacement by the complete part number and the installed equipment configuration. A similar photograph or a shared LiftMaster brand name does not establish interchangeability. Confirm the applicable service drawing before ordering so the repair addresses the correct component and its related mounting, connection and operating requirements.
Compatibility — Models, Versions and Exclusions
| Model or selection point | Compatibility requirement |
|---|---|
| Flat-surface attachment | Confirm both mounting faces suit the gate and support geometry. |
| Gate loading | Evaluate gate weight and the manufacturer’s complete installation requirements. |
| Post and gate structure | Both require suitable strength, alignment and attachment provisions. |
| Other hinge series | Do not transfer capacities or geometry from heavier LiftMaster hinge models. |
Identify the Assembly and Plan the Repair
Hinge capacity must be considered together with the gate’s size, loading, support and attachment design. A suitable hinge cannot compensate for a weak post or a distorted gate frame. Have the installer check the intended hinge spacing, opening clearance and structural condition before selecting the final mounting arrangement.
The flat-on-both-sides configuration is a geometry choice, not a guarantee that every existing hinge location will accept the replacement. Compare the physical dimensions and attachment requirements with the current manufacturer drawing. Preserve access for lubrication and inspection; do not assume that a roller-bearing hinge is maintenance-free or that a stainless designation identifies a specific alloy grade.
Compare the replacement with the installed service arrangement before dismantling the equipment. Photograph the part’s location and record the complete model and visible service numbers. Inspect the surrounding attachment points and mating components for wear, impact damage or misalignment. Replacing one worn item will not correct a damaged support or another component that continues to impose abnormal loads on the repaired assembly.
Specifications and Product Identification
| Specification | Details |
|---|---|
| Ordering reference | 2180SS |
| Material designation | Stainless steel; specific grade not stated here |
| Mounting style | Flat on both sides |
| Ordering unit | Pair |
| Published capacity | 1,000 lb per pair |
| Bearing arrangement | Roller-bearing hinge design |
Before Ordering
- Confirm that a pair is the intended purchasing unit.
- Check flat mounting faces and required hinge dimensions.
- Have gate and post loading assessed for the actual installation.
- Plan alignment, lubrication access and safe gate support during fitting.
Package Contents and Separate Requirements
The 2180SS ordering unit is a pair of the identified stainless specialty hinges. Do not assume that gate posts, reinforcement plates, anchors, welding materials or an automatic operator are included. Confirm the current supplied attachment hardware, if any, and obtain the structural materials specified for the actual gate and support.
Safety Warnings — Read Before Installation or Service
- WARNING: A moving gate and exposed stainless steel specialty gate hinges — flat both sides, pair can cause serious injury. Installation and service require a qualified gate-systems technician.
- Isolate AC power, batteries and any solar supply as applicable, and secure the gate against unexpected movement before work begins.
- Support the gate securely before removing hinges. Have the installer verify posts, attachment and gate loading; the published pair capacity does not establish structural adequacy for the whole installation.
- Restore all covers and guards, then verify travel endpoints, reversal and every required safety device before returning the gate to normal operation.
Related Products and Important Differences
- LMRRUL monitored photo eye — a separate protection option only where the exact operator and control revision approve it; not a universal legacy retrofit.
- LMWEKITU monitored wireless edge kit — a separate edge communication system for approved controls and resistive edges; not a replacement for this mechanical or electrical service part.
Frequently Asked Questions
Is 1,000 lb the capacity of one hinge?
The published capacity is per pair. Do not double that figure or apply it to a single hinge.
Are both mounting sides flat?
Yes, that is the identified 2180SS configuration. Compare dimensions and clearances before replacing a different hinge geometry.
Is the stainless grade specified?
No particular alloy grade is claimed here. Obtain current manufacturer material information if the project requires a documented grade.
Does the pair include installation structure?
No gate frame or support structure is identified. The installer must provide the suitable support and attachment arrangement for the project.
Need Help Confirming the Right Product?
Contact Garage-DoorParts.com before ordering. Send the full equipment model, readable part labels and photographs of the installed assembly. Include the dimensions, electrical configuration or accessory details relevant to your project so the listing can be checked against the actual installation.
Details
Need Help With Compatibility?
Not sure if this is the correct part for your garage door, operator, gate system, or application? Contact Us before ordering — we’re happy to help.
Garage-DoorParts.com carries a large selection of residential and commercial parts, and many components can look similar while having important differences in dimensions, model numbers, voltage, mounting, or compatibility.
For the best assistance, please provide as much information as possible, including the manufacturer, model number, part number, door or operator type, dimensions, and clear photos of the existing part or equipment.
Our goal is to help you identify the correct product before you order and reduce the possibility of ordering an incompatible part.
Contact Us with your product questions and compatibility information, and we’ll do our best to point you in the right direction.
Shipping & Returns
We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.
We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.