LiftMaster 2062P Gorilla Gate Hinge — Bolt To Gate And Bolt To Post, Prime Coated

The LiftMaster 2062P is the prime-coated Gorilla-series roller-bearing gate hinge with bolt to gate and bolt to post geometry. The documented ordering quantity is one hinge. It supports the specified gate pivot arrangement, separate from the gate operator and access controls. Match the actual gate, post and structural attachment before ordering, and do not transfer a capacity or mounting detail from another hinge merely because both are described as heavy duty. Select the replacement by the complete part number and the installed equipment configuration. A similar photograph or a shared LiftMaster brand name does not establish interchangeability. Confirm the applicable service drawing before ordering so the repair addresses the correct component and its related mounting, connection and operating requirements.

Compatibility — Models, Versions and Exclusions

Identify the Assembly and Plan the Repair

The welded-pin design and compact hinge layout do not establish the strength of the gate frame, post or foundation. Inspect those structures and evaluate gate width and loading before replacing hinges. A pair rating applies to an appropriate complete installation and must not be applied to one individual hinge or to unsuitable supports.

The bolt to gate and bolt to post arrangement must agree with the fabrication and attachment plan. Support and secure the gate before loosening existing hinges, align the hinge axes and check clearance through the required swing. Prime coating identifies the supplied finish and does not remove the need for appropriate finishing, lubrication and periodic inspection.

Compare the replacement with the installed service arrangement before dismantling the equipment. Photograph the part’s location and record the complete model and visible service numbers. Inspect the surrounding attachment points and mating components for wear, impact damage or misalignment. Replacing one worn item will not correct a damaged support or another component that continues to impose abnormal loads on the repaired assembly.

Plan the repair around the manufacturer’s instructions for the actual equipment revision. Confirm access, safe support and any separate hardware before removing the old part. After installation, restore the intended retention, alignment and guarding, then test the equipment under controlled conditions. The repair is complete only when the original fault has been addressed and the system’s required operating and protection functions have been checked.

Specifications and Product Identification

Before Ordering

• Confirm gate weight, width and structural condition.
• Match the exact mounting geometry.
• Verify the individual-versus-pair ordering quantity.
• Review attachment, alignment, finishing and maintenance requirements.

Package Contents and Separate Requirements

The manufacturer hardware catalog identifies one hinge for this reference. Gate, post, operator, reinforcement, fabrication materials and support equipment are separate. Confirm current attachment hardware with the supplier. An individual 2062P order is not automatically a two-hinge package, and a 2064P pair should not be interpreted as a complete gate-support system.

Safety Warnings — Read Before Installation or Service

• WARNING: A falling or uncontrolled gate can cause serious injury or death. A qualified gate professional must support and secure it before removing any hinge.
• Isolate automated-gate power and prevent movement during structural work. Never rely on the operator arm as the sole gate support.
• Use the prescribed structural attachment and align the hinge axes. Do not transfer another hinge’s capacity or use adjustment to conceal damaged supports.
• Verify smooth gate movement, secured retention and all required automation protection before returning the installation to normal use.

Related Products and Important Differences

• LMRRUL monitored photo eye — a separate protection option only where the exact operator and control revision approve it; not a universal legacy retrofit.
• LMWEKITU monitored wireless edge kit — a separate edge communication system for approved controls and resistive edges; not a replacement for this mechanical or electrical service part.

Frequently Asked Questions

Is the capacity a per-hinge rating?

No. The stated series rating applies per pair in a suitable installation.

Does prime coating mean no finishing is needed?

No. Plan the appropriate completed finish and maintenance.

Does the hinge repair a leaning post?

No. Supporting structure needs separate assessment.

Can a similar hinge geometry be substituted?

Use the exact mounting design and approved structural attachment.

Need Help Confirming the Right Product?

Contact Garage-DoorParts.com before ordering. Send the full equipment model, readable part labels and photographs of the installed assembly. Include the dimensions, electrical configuration or accessory details relevant to your project so the listing can be checked against the actual installation.