LiftMaster 12-2002 Sleeve Bearing — SW470 / SW490 Main-Shaft Service
The LiftMaster 12-2002 is the sleeve-bearing service reference identified in the documented SW470 and SW490 swing-gate operator main-shaft arrangements. The manufacturer parts description uses a 1-1/2-inch by 1-3/4-inch designation. Match the exact service drawing and bearing location before purchase; that two-number description does not provide every dimension or establish interchangeability with a flange bearing or another shaft-support component. Select the replacement by the complete part number and the installed equipment configuration. A similar photograph or a shared LiftMaster brand name does not establish interchangeability. Confirm the applicable service drawing before ordering so the repair addresses the correct component and its related mounting, connection and operating requirements.
Compatibility — Models, Versions and Exclusions
| Model or selection point | Compatibility requirement |
|---|---|
| SW470 / SW490 | Match 12-2002 at the correct main-shaft callout. |
| Other shaft supports | Do not substitute the flange-bearing or extension-sleeve reference. |
| Dimension check | Confirm complete shaft and housing fit, including unstated length. |
| Other swing operators | No universal sleeve-bearing fit is established. |
Identify the Assembly and Plan the Repair
A sleeve bearing supports the matching shaft within the documented assembly; it is not the same service component as the separately listed flange bearing. Inspect the shaft surface and the bearing seat before replacing the worn sleeve. Scoring, an enlarged support or poor alignment can prevent a replacement bearing from restoring the intended shaft support.
Use the full operator label and correct revision of the main-shaft drawing to identify the location and quantity required. Do not convert an illustrated quantity into a supplied package count. The published size designation is useful for comparison, but obtain any missing dimensions and approved fitting instructions before dismantling the mechanism. Follow the manufacturer’s requirements for the actual shaft and housing rather than assume a lubrication or installation method.
Compare the replacement with the installed service arrangement before dismantling the equipment. Photograph the part’s location and record the complete model and visible service numbers. Inspect the surrounding attachment points and mating components for wear, impact damage or misalignment. Replacing one worn item will not correct a damaged support or another component that continues to impose abnormal loads on the repaired assembly.
Specifications and Product Identification
| Specification | Details |
|---|---|
| Ordering reference | 12-2002 |
| Component | Sleeve bearing |
| Documented application | SW470 / SW490 main-shaft arrangement |
| Published size designation | 1-1/2 inch x 1-3/4 inch |
| Unstated dimensions | Confirm overall length and complete fit requirements |
| Separate service references | 12-2125 flange bearing; 12-10172 extension sleeve |
Before Ordering
- Record the full SW470 / SW490 model and service revision.
- Locate the 12-2002 sleeve-bearing callout.
- Check the complete dimensions and shaft/support condition.
- Confirm current supplied quantity and approved fitting procedure.
Package Contents and Separate Requirements
This offer identifies the 12-2002 sleeve-bearing service item. Confirm the current quantity supplied. A flange bearing, extension sleeve, shaft, housing, crank and complete operator are not established as included. Order related worn components separately only after checking the actual shaft-support arrangement and the cause of wear.
Safety Warnings — Read Before Installation or Service
- WARNING: A moving gate and exposed sleeve bearing — sw470 / sw490 main-shaft service can cause serious injury. Installation and service require a qualified gate-systems technician.
- Isolate AC power, batteries and any solar supply as applicable, and secure the gate against unexpected movement before work begins.
- Keep people clear of the gate and drive during supervised testing. Never bypass required entrapment-protection devices or increase force to overcome a mechanical fault.
- Restore all covers and guards, then verify travel endpoints, reversal and every required safety device before returning the gate to normal operation.
Related Products and Important Differences
- LMRRUL monitored photo eye — a separate protection option only where the exact operator and control revision approve it; not a universal legacy retrofit.
- LMWEKITU monitored wireless edge kit — a separate edge communication system for approved controls and resistive edges; not a replacement for this mechanical or electrical service part.
Frequently Asked Questions
Is this a flange bearing?
No. The researched service drawing identifies 12-2002 as the sleeve bearing and gives the flange bearing a separate reference.
Does the size designation include length?
The two published numbers do not establish every dimension. Confirm the complete fit, including length, from the approved service reference.
Does a diagram quantity show the package quantity?
No. Confirm the number supplied in the current offer separately from the number used in the machine.
Will a new sleeve repair a damaged shaft?
No. Inspect the shaft surface, support and alignment so the new bearing is not installed against an unresolved fault.
Need Help Confirming the Right Product?
Contact Garage-DoorParts.com before ordering. Send the full equipment model, readable part labels and photographs of the installed assembly. Include the dimensions, electrical configuration or accessory details relevant to your project so the listing can be checked against the actual installation.
Details
Need Help With Compatibility?
Not sure if this is the correct part for your garage door, operator, gate system, or application? Contact Us before ordering — we’re happy to help.
Garage-DoorParts.com carries a large selection of residential and commercial parts, and many components can look similar while having important differences in dimensions, model numbers, voltage, mounting, or compatibility.
For the best assistance, please provide as much information as possible, including the manufacturer, model number, part number, door or operator type, dimensions, and clear photos of the existing part or equipment.
Our goal is to help you identify the correct product before you order and reduce the possibility of ordering an incompatible part.
Contact Us with your product questions and compatibility information, and we’ll do our best to point you in the right direction.
Shipping & Returns
We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.
We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.