LiftMaster 100MAPS External Power Supply — LC-36A /PRE-SENSOR
The LiftMaster 100MAPS is the external power-supply accessory identified by the manufacturer for the LC-36A light curtain or PRE-SENSOR trailer-presence sensor. The current product page describes a 100mA supply with a 28-foot cord and support for up to two of the specified devices. Match the exact sensor arrangement and current instructions before ordering. It is not a universal12V accessory supply or a sensor by itself. Powering a light curtain does not replace the operator’s required primary monitored protection or establish the complete sensing interface.
Compatibility — Models, Versions and Exclusions
| Model or selection point | Compatibility requirement |
|---|---|
| LC-36A approved arrangements | Match exact supply and interface requirements. |
| PRE-SENSOR | Manufacturer-listed supply application. |
| Medium-duty operator installations | Check required separate supply and interface instructions. |
| Primary monitored protection | Not replaced by this supply orancillary light curtain. |
| Unrelated accessories | No universal voltage/current compatibility established. |
Plan Sensor Power and the Operator Interface Separately
Record the operator and sensor models and identify how many devices must be powered. Have the installer check the current sensor and supply instructions rather than borrowing a cord length orvoltage from older catalog literature. A power supply can provide the documented source while the signal connection to the operator still requires its own approved interface.
Inspect the proposed cable route, mounting and protection from moving equipment. Do not extend the cord orconnect an unrelated load without documented permission. After installation, verify the sensor response through its approved interface and test the operator’s required primary protection independently. A powered indicator or a working trailer-presence signal does not prove that the doorway is clear or that the required stopping/reversal functions have been checked.
Specifications and Product Identification
| Specification | Details |
|---|---|
| Model | 100MAPS |
| Product | External sensor power supply |
| Manufacturer designation | 100mA |
| Current product-page cord | 28 feet |
| Documented devices | LC-36A /PRE-SENSOR |
| Stated device capacity | Up to two specified devices;follow exact instructions |
Before Ordering
- Record operator and LC-36A orPRE-SENSOR details.
- Confirm current100MAPS supply and 28-foot cord requirement.
- Determine device count and approved signal interface.
- Plan secure routing and complete sensor/protection tests.
Package Contents and Separate Requirements
This offer identifies the 100MAPS external power supply with its documented cord. The LC-36A light curtains, PRE-SENSOR, interface board, field mounting hardware and complete operator are not promised as included. Confirm current connection pieces and package instructions before ordering. The capacity to power up to two approved devices does not mean two sensors accompany the supply or that every possible pair of accessories may be connected.
Safety Warnings — Read Before Installation or Service
- WARNING: Sensor power and signal interfaces must match the approved operator arrangement. Use qualified personnel.
- Isolate applicable power before wiring and route the supply cord clear ofdoors, vehicles and moving hardware.
- Do not bypass primary monitored protection oruse this supply as proof that an ancillary device is a primary safety system.
- Test the supplied sensors through the approved interface and all separately required operator safety functions before use.
Related Products and Important Differences
- CPS-U monitored photo eyes — separate protection devices for approved commercial-door controls; match the operator and environment.
- TDC12X1BMC MAXUM trolley operator — a complete-operator comparison, not evidence that this legacy service part fits MAXUM.
Frequently Asked Questions
Are light curtains included?
No. This is the external supply.
What cord length does the current page state?
28 feet.
Can it power two approved devices?
The manufacturer states up to two LC-36A orPRE-SENSOR devices;follow exact instructions.
Does it replace primary protection?
No. Power and ancillary sensing do not replace required primary monitored devices.
Need Help Confirming the Right Product?
Contact Garage-DoorParts.com before ordering. Send the full equipment model, readable part labels and photographs of the installed assembly. Include the dimensions, electrical configuration or accessory details relevant to your project so the listing can be checked against the actual installation.
Details
Need Help With Compatibility?
Not sure if this is the correct part for your garage door, operator, gate system, or application? Contact Us before ordering — we’re happy to help.
Garage-DoorParts.com carries a large selection of residential and commercial parts, and many components can look similar while having important differences in dimensions, model numbers, voltage, mounting, or compatibility.
For the best assistance, please provide as much information as possible, including the manufacturer, model number, part number, door or operator type, dimensions, and clear photos of the existing part or equipment.
Our goal is to help you identify the correct product before you order and reduce the possibility of ordering an incompatible part.
Contact Us with your product questions and compatibility information, and we’ll do our best to point you in the right direction.
Shipping & Returns
We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.
We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.