LiftMaster 041A5047 Door-Bracket Installation Kit — Bracket, Clevis Pin and Push Ring

LiftMaster 041A5047 Door-Bracket Installation Kit — Bracket, Clevis Pin and Push Ring

$20.58
Skip to product information
LiftMaster 041A5047 Door-Bracket Installation Kit — Bracket, Clevis Pin and Push Ring

LiftMaster 041A5047 Door-Bracket Installation Kit — Bracket, Clevis Pin and Push Ring

041A5047
$20.58
Shipping calculated at checkout.

The LiftMaster 041A5047 is the door-bracket installation kit identified by the manufacturer for selected LiftMaster and Chamberlain garage-door openers. Its listed inventory is the bracket, clevis pin and push ring. It connects at the documented door-arm attachment, separate from the header bracket and opener support hardware. Confirm the opener instructions and the door’s reinforcement requirements before selecting the bracket for a repair. Select the replacement by the complete part number and the installed equipment configuration. A similar photograph or a shared LiftMaster brand name does not establish interchangeability. Confirm the applicable service drawing before ordering so the repair addresses the correct component and its related mounting, connection and operating requirements.

Compatibility — Models, Versions and Exclusions

Model or selection point Compatibility requirement
Manufacturer-listed opener arrangements Match the exact model and door-arm configuration.
Lightweight or sectional door attachment Follow the door manufacturer’s reinforcement requirements.
Header bracket Different mounting position and service item.
041A5047-1 or other variants Do not assume every suffix identifies an identical offer.

Identify the Assembly and Plan the Repair

Inspect the door attachment area if the old bracket has pulled loose or bent. The replacement metal bracket cannot repair torn skin, a cracked panel or unsuitable backing. Have the installer determine whether reinforcement or other structural service is needed before fitting the new part.

The clevis connection must permit the prescribed door-arm movement without binding. Restore the intended bracket position and retention rather than relocating it to compensate for an incorrectly adjusted arm or damaged door. Follow the exact opener and door instructions and verify travel and reversal after service.

Compare the replacement with the installed service arrangement before dismantling the equipment. Photograph the part’s location and record the complete model and visible service numbers. Inspect the surrounding attachment points and mating components for wear, impact damage or misalignment. Replacing one worn item will not correct a damaged support or another component that continues to impose abnormal loads on the repaired assembly.

Plan the repair around the manufacturer’s instructions for the actual equipment revision. Confirm access, safe support and any separate hardware before removing the old part. After installation, restore the intended retention, alignment and guarding, then test the equipment under controlled conditions. The repair is complete only when the original fault has been addressed and the system’s required operating and protection functions have been checked.

Specifications and Product Identification

Specification Details
Ordering reference 041A5047
Component Door bracket
Manufacturer inventory Bracket, clevis pin and push ring
Listed examples 8160, 8155, 8165 and 8365; verify exact configuration
Separate requirement Suitable door reinforcement and approved attachment

Before Ordering

  • Confirm the exact opener service reference.
  • Inspect door structure and reinforcement.
  • Match the arm connection and bracket position.
  • Verify the documented bracket/pin/ring inventory.

Package Contents and Separate Requirements

The manufacturer lists a door bracket, clevis pin and push ring. Door reinforcement, complete arm assembly, header bracket, rail, opener and site-specific structural fasteners are separate unless expressly included. Do not assume every screw shown elsewhere in an installation diagram ships with this bracket kit.

Safety Warnings — Read Before Installation or Service

  • WARNING: A moving commercial door and exposed door-bracket installation kit — bracket, clevis pin and push ring can cause serious injury or death. Have a trained door-systems technician perform installation and service.
  • Disconnect mains power and any battery backup before mechanical work or wiring. Secure the door against unexpected movement as directed by its manufacturer.
  • Do not work on springs, cables or counterbalance components without appropriate training. Never bypass safety sensors or increase force to overcome binding.
  • Restore guards and complete the model-specific travel, reversal and protection-device tests before returning the door to normal operation.

Related Products and Important Differences

Frequently Asked Questions

What is included?

The manufacturer identifies the bracket, clevis pin and push ring.

Is this the header bracket?

No. It attaches at the specified door-arm connection.

Will it repair a torn panel?

No. Door structure and reinforcement require separate assessment.

Can I use it on every opener?

No. Check the exact model and attachment instructions.

Need Help Confirming the Right Product?

Contact Garage-DoorParts.com before ordering. Send the full equipment model, readable part labels and photographs of the installed assembly. Include the dimensions, electrical configuration or accessory details relevant to your project so the listing can be checked against the actual installation.

Details

Need Help With Compatibility?

Not sure if this is the correct part for your garage door, operator, gate system, or application? Contact Us before ordering — we’re happy to help.

Garage-DoorParts.com carries a large selection of residential and commercial parts, and many components can look similar while having important differences in dimensions, model numbers, voltage, mounting, or compatibility.

For the best assistance, please provide as much information as possible, including the manufacturer, model number, part number, door or operator type, dimensions, and clear photos of the existing part or equipment.

Our goal is to help you identify the correct product before you order and reduce the possibility of ordering an incompatible part.

Contact Us with your product questions and compatibility information, and we’ll do our best to point you in the right direction.

Shipping & Returns

We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.

We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.

Related products