SSC 7' Garage Door Extension Spring – 100 lb – 25-42 Series – Tan – Clips Included

🇺🇸 Made in USA

This SSC garage door extension spring is designed for compatible sectional garage doors approximately 7 feet highrequiring a 100 lb spring rating.

Manufactured by Service Spring Corporation (SSC), this spring belongs to the 25-42 Series and features a clipped-end configuration with clips included for compatible extension-spring installations.

The spring is manufactured from black-coated, oil-tempered spring wire, uses the Tan identification color for the 100 lb rating, and is rated for a minimum of 10,000 operating cycles.

Specifications

25-42 Series for 7' High Doors

This spring is part of SSC's 25-42 Series, designed for compatible 7-foot-high sectional garage doors.

The 25-42 designation identifies the spring series and should not be treated as a literal physical measurement.

Correct replacement should be based on the complete spring specification, including:

• Door height

• Spring series

• Required pull rating

• End configuration

• Existing spring setup

• Door counterbalance requirements

100 lb Pull Rating

This spring provides a 100 lb pull rating.

Correct spring strength is essential for proper garage door balance. Installing a spring with too little or too much lifting force can result in:

• Heavy manual operation

• A door that rises unexpectedly

• Uneven lifting

• Incorrect cable tension

• Excessive garage door opener strain

• Premature pulley and hardware wear

Always verify the required spring rating before ordering.

Tan Color Code

The Tan identification color corresponds to the 100 lb extension-spring rating for this configuration.

Extension-spring colors repeat at different weight ranges, so color alone should never determine the correct replacement spring.

Before ordering, confirm:

• 7' door application

• 25-42 Series

• 100 lb pull rating

• Tan identification

• Clipped-end configuration

Clipped Ends – Clips Included

This 110CL version features clipped ends and includes clips for compatible installations.

It differs from other 100 lb SSC configurations such as:

• 110 – Double-loop ends

• 1100 – Open-loop ends

• 110CL – Clipped ends

Always compare your existing spring and attachment hardware before ordering.

How Extension Springs Work

Extension springs are typically installed alongside the horizontal tracks on both sides of a sectional garage door.

As the door closes, the springs stretch and store mechanical energy. As the door opens, that stored energy assists in lifting and counterbalancing the weight of the door.

A correctly matched extension-spring system helps provide:

• Smooth door travel

• Proper counterbalance

• Correct cable tension

• Easier manual operation

• Reduced strain on the garage door opener

Compatibility & Fitment

Extension springs are not universal.

This spring should be selected when your system specifically requires:

• 7' high garage door

• 25-42 Series

• 100 lb pull rating

• Tan color code

• Clipped ends with clips

Also inspect the existing:

• Lift cables

• Pulleys

• Safety containment cables

• Spring attachment points

• Track hardware

• Rear supports

• Fasteners

Replace worn or damaged components before returning the door to service.

Replace Extension Springs in Pairs

For garage doors using two extension springs, replacing both springs as a matching pair is generally recommended.

Both springs normally experience approximately the same number of operating cycles. If one spring fails or weakens, the opposite spring may already be fatigued.

Using one new spring with one worn spring can cause:

• Uneven lifting force

• Unequal cable tension

• Crooked door travel

• Poor door balance

• Increased hardware wear

Safety Cables Strongly Recommended

Extension-spring systems should use properly installed safety containment cables running through each spring.

If an extension spring breaks, the safety cable helps contain the spring and reduces the risk of it becoming a dangerous projectile.

Inspect existing safety cables whenever replacing extension springs.

Ready to Order?

If your existing system requires a 7' door, SSC 25-42 Series extension spring, 100 lb rating, Tan identification, and clipped-end configuration, this spring is ready for your repair.

Add it to your cart today and restore proper garage door counterbalance with the correct SSC-made extension spring.

Before ordering, double-check:

• 7' door height

• 25-42 Series

• 100 lb pull rating

• Tan color code

• Clipped ends

• Clips required

Safety Warning

⚠️ Garage door extension springs operate under substantial tension and can cause severe injury, death, or property damage if improperly handled.

Never remove an extension spring, pulley, lift cable, clip, or attachment point while the spring is stretched.

Secure the garage door and fully release spring tension before servicing the system.

Installation should be performed by a qualified person familiar with garage door extension springs, safety containment cables, and proper installation procedures.