SSC .2625 x 1.75″ ID x 37″ Torsion Spring – Right Wind – Blue
SSC .2625 x 1.75″ ID x 37″ Torsion Spring – Right Wind – Blue
Manufactured by Service Spring Corporation (SSC), this .2625″ wire x 1.75″ inside diameter x 37″ right-wind torsion spring is designed for a compatible sectional door counterbalance system requiring these specifications.
🇺🇸 Made in USA
This spring features coated, oil-tempered wire and installed winding and stationary cones. It must be selected according to the door’s complete counterbalance requirements, including any companion spring and the cable-drum arrangement.
Features & Benefits
-
.2625″ wire diameter.
-
Blue wire-size identification.
-
1.75″ inside diameter.
-
37″ unwound spring-body length.
-
Right-wind configuration.
-
Winding and stationary cones installed.
-
Coated, oil-tempered wire.
-
Standard-cycle spring listed for a minimum 10,000-cycle application when correctly selected.
One opening and closing equals one cycle. Actual service life depends on spring loading, operating turns, maintenance, installation, and corrosion exposure.
Specifications
| Specification | Detail |
|---|---|
| Manufacturer | SSC — Service Spring Corporation |
| Wire diameter | .2625″ |
| Inside diameter | 1.75″ |
| Spring-body length | 37″, unwound, excluding cones |
| Winding direction | Right Wind — RW |
| Wire-size color | Blue |
| Wire construction | Coated, oil-tempered |
| Cones | Winding and stationary cones installed |
| Cycle classification | Standard cycle; listed minimum 10,000 cycles |
Common Uses
For replacement of a matching right-wind torsion spring on a compatible sectional overhead door. Door weight, height, track configuration, drum specifications, and the complete spring combination determine suitability.
This spring does not carry a universal lifting-capacity rating independent of the system in which it is installed.
Compatibility & Selection
Confirm .2625″ wire, 1.75″ ID, 37″ unwound body length, and right wind. Also check shaft fit, cone compatibility, stationary mounting, and clearance for spring operation.
A .2625″ wire spring with a 2″ ID has different operating characteristics and is not automatically an equivalent replacement. Likewise, the left-wind version cannot be installed in the same position simply because its dimensions match.
Right wind describes coil direction rather than the spring’s physical position on the door. Verify the required winding direction from the system layout.
Pairing & Replacement Notes
For a two-spring system, verify the required combined torque before selecting the companion. Equal-size opposite-wind springs are common, but unequal pairs may be correct for particular doors.
Evaluate both springs when replacing a failed spring, especially when both are the same age. Higher-cycle options require a calculated replacement, not an arbitrary change in body length or wire diameter.
High-lift or vertical-lift applications and drum changes must be evaluated separately.
Installation & Safety
Professional installation is strongly recommended. Torsion springs store hazardous energy and require proper winding bars, training, and manufacturer-approved procedures.
Do not loosen loaded cones, drums, cables, or bottom fixtures. Following installation, the technician should check balance throughout travel, cable seating, hardware clearances, and opener safety operation.
Order this SSC right-wind spring once its dimensions and system fit are confirmed. Contact us with measurements and photos if you need help selecting the correct replacement.
SSC .2625 x 1.75″ ID x 37″ Right-Wind Torsion Spring – Blue
Shop an American-made SSC torsion spring with coated wire and installed cones. Confirm inside diameter, length, and winding direction before purchasing.
Details
Need Help With Compatibility?
Not sure if this is the correct part for your garage door, operator, gate system, or application? Contact Us before ordering — we’re happy to help.
Garage-DoorParts.com carries a large selection of residential and commercial parts, and many components can look similar while having important differences in dimensions, model numbers, voltage, mounting, or compatibility.
For the best assistance, please provide as much information as possible, including the manufacturer, model number, part number, door or operator type, dimensions, and clear photos of the existing part or equipment.
Our goal is to help you identify the correct product before you order and reduce the possibility of ordering an incompatible part.
Contact Us with your product questions and compatibility information, and we’ll do our best to point you in the right direction.
Shipping & Returns
We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.
We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.
Shop The Full Collection
