Right-Wind Garage Door Torsion Spring — .2437 Wire × 2-Inch ID × 30.25-Inch Length, Green, Coated, Cones Installed
Right-Wind Garage Door Torsion Spring — .2437 Wire × 2-Inch ID × 30.25-Inch Length, Green, Coated, Cones Installed
Spring Specifications
| Wire Size | .2437" |
| Inner Diameter (ID) | 2.00" |
| Length | 30.25" |
| Color Code | Green |
| Winding | Right Wind |
- Made in the USA
- All springs rated for an industry standard minimum lifecycle of 10,000 cycles
- Springs come with winding and stationary cones installed and are stenciled and color coded for easy identification
- Coated & oil tempered wire
-
Right-Wind Garage Door Torsion Spring — .2437 Wire × 2-Inch ID × 30.25-Inch Length, Green, Coated, Cones Installed
Spring Specifications
- Wind direction: Right wind
- Wire size: .2437 inch
- Wire color code: Green
- Inside diameter: 2 inches
- Spring length: 30.25 inches
- Spring type: Standard torsion spring
- Wire material: Oil-tempered spring wire
- Finish: Coated
- Winding cone: Installed
- Stationary cone: Installed
- Minimum rated lifecycle: 10,000 cycles
- Country of manufacture: USA
- Application: Residential and light-commercial sectional garage doors
- Quantity: One torsion spring
Product Description
This right-wind garage door torsion spring is designed for sectional garage door systems requiring a .2437-inch wire size, 2-inch inside diameter, and 30.25-inch spring length.
The spring is manufactured in the USA from coated, oil-tempered wire for reliable lifting performance and improved protection against corrosion, surface residue, and normal environmental exposure.
The .2437-inch wire size is identified by a green color code for easier reference. However, color coding should never be used as the only method for selecting a replacement spring.
The winding cone and stationary cone are already installed, making the spring ready for professional installation once its specifications have been properly matched to the garage door’s weight, height, cable drums, track configuration, and required torque.
Size / Specification Chart
Specification Measurement Wind direction Right wind Wire size .2437 inch Wire color code Green Inside diameter 2 inches Spring body length 30.25 inches Spring type Standard torsion spring Wire type Oil tempered Finish Coated Winding cone Installed Stationary cone Installed Minimum lifecycle 10,000 cycles Quantity One spring Common Uses
This torsion spring may be used in properly engineered spring systems for:
- Residential sectional garage doors
- Light-commercial overhead doors
- Single-car garage doors
- Two-car garage doors
- Workshop and service-bay doors
- Storage-building doors
- Single-spring torsion systems
- Two-spring torsion systems
- Standard-lift garage door systems
Actual compatibility depends on the complete spring calculation and not only the width, height, weight, or appearance of the garage door.
Compatibility & Fitment
This torsion spring is compatible only with garage door systems engineered for all of the following specifications:
- .2437-inch wire diameter
- 2-inch inside diameter
- 30.25-inch spring body length
- Right-wind configuration
- Compatible torsion shaft and cone bore
- Correct cable drums
- Correct track and lift configuration
- Correct torque requirement for the garage door’s weight
Correct torsion spring selection depends on:
- Actual garage door weight
- Garage door height
- Cable drum model
- Track configuration
- Standard-lift, high-lift, or vertical-lift setup
- Number of springs in the system
- Wire diameter
- Inside diameter
- Spring body length
- Required inch-pounds per turn
- Intended cycle life
Do not select a replacement spring based only on the door size, spring color, mounting position, or visual similarity.
Important Matching Notes
A right-wind torsion spring is commonly installed on the left side of the center support bracket when viewed from inside the garage facing the closed door. Spring placement can vary depending on the torsion-system design.
Always verify the wind direction from the spring itself rather than relying only on its mounting location.
Measure the spring body only after all tension has been safely removed. Measure only the wound coils from one end to the other. Do not include the winding cone or stationary cone in the spring-length measurement.
The green marking identifies the .2437-inch wire size, but the wire diameter should still be physically measured and confirmed before ordering.
A spring with the wrong wire size, inside diameter, length, or wind direction may prevent the door from balancing correctly and can overload the garage door opener, cables, drums, bearings, or other hardware.
When replacing one spring in a two-spring system, verify the size, wind direction, age, and condition of both springs. Replacing both springs as a properly matched pair may provide more consistent lifting force, balance, and service life.
Installation Notes
This spring includes the winding cone and stationary cone. It does not include:
- Winding bars
- Torsion shaft
- Center bearing
- Center support bracket
- End bearing plates
- Cable drums
- Lift cables
- Bottom fixtures
- Mounting fasteners
Before installation, inspect the torsion shaft, bearings, drums, cables, brackets, bottom fixtures, and attachment points for wear, corrosion, deformation, or damage.
After installation, disconnect the automatic opener and test the garage door manually. A properly balanced door should move smoothly and remain near the halfway-open position without rapidly rising or falling.
The correct number of winding turns and final spring adjustment must be determined from the garage door height, drum configuration, spring engineering, and manufacturer requirements.
Safety Warning
Garage door torsion springs store extreme mechanical energy. Improper removal, installation, winding, or adjustment can cause severe injury, death, or property damage.
Installation should be performed only by a trained garage door technician using correctly sized solid-steel winding bars and established safety procedures.
Never use screwdrivers, ratchets, socket extensions, rebar, or improvised tools to wind or unwind a torsion spring.
Right-Wind Garage Door Torsion Spring .2437 × 2 × 30.25 Inches with Cones
Right-wind garage door torsion spring with .2437-inch green-coded wire, 2-inch inside diameter, 30.25-inch length, coated oil-tempered wire, and installed winding and stationary cones.
Details
This product is crafted with quality materials to ensure durability and performance. Designed with your convenience in mind, it seamlessly fits into your everyday life.
Shipping & Returns
We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.
We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.
Shop The Full Collection
