SSC .2070 x 1.75" ID x 31" Torsion Spring – Right Wind (RW) – Yellow

🇺🇸 Made in USA

This Right Wind (RW) torsion spring is manufactured by Service Spring Corporation (SSC) for sectional overhead door torsion systems requiring a .2070" wire size, 1.75" inside diameter, and 31" spring length.

Manufactured from coated, oil-tempered spring wire, this spring includes the winding cone and stationary cone installed and is rated for an industry-standard minimum lifecycle of 10,000 cycles.

The .2070" wire size uses the Yellow DASMA color code. Color should be used only as an identification aid—always verify wire diameter, inside diameter, spring length, wind direction, and required spring specifications before ordering.

Spring Specifications

Application

Designed for torsion-spring counterbalance systems where the calculated requirements call for a Right Wind .2070" x 1.75" ID x 31" torsion spring.

This spring may be used in residential or light commercial sectional door systems when its torque characteristics correctly match the door weight, height, cable drums, track configuration, and overall counterbalance requirements.

Compatibility & Fitment

Garage door torsion springs are not universal replacement parts.

Correct replacement requires matching or properly recalculating:

• Wire diameter

• Inside diameter

• Spring length

• Wind direction

• Door weight

• Door height

• Cable drum type

• Track configuration

• Number of springs

• Required torque / IPPT

• Available shaft and spring space

Two springs that appear similar can produce significantly different torque and should not be considered interchangeable without proper calculations.

Right-Wind Identification

This is a Right Wind (RW) torsion spring.

On a conventional torsion system, a right-wound spring is typically installed on the left side of the center support when viewed from inside the garage looking toward the door.

System configurations can vary, so always verify the actual spring wind before ordering.

Yellow Wire Color Code

The Yellow DASMA color code corresponds to .2070" wire size.

Do not select a replacement spring based on color alone. Paint markings may fade, become dirty, or be confused with other markings.

For accurate replacement, physically verify:

• Wire size

• Inside diameter

• Unwound spring length

• Wind direction

Important Matching Notes

When replacing one spring in a two-spring system, inspect and identify the opposite spring as well.

Paired torsion springs normally use opposite wind directions, but the two springs are not necessarily identical in every installation.

Changing the wire size, inside diameter, or spring length changes the spring's torque characteristics. Substitute sizes should only be used after the door's counterbalance requirements have been properly calculated.

Cones Installed

This spring is supplied with both the winding cone and stationary cone installed.

Proper installation requires correctly sized torsion-spring winding bars and knowledge of:

• Spring winding

• Shaft positioning

• Cable drum setup

• Cable tension

• Bearing alignment

• Door balancing

After installation, verify that the cables remain correctly seated on the drums and that the door is properly balanced throughout its travel.

Ready to Order?

If your existing spring matches the .2070" wire size, 1.75" inside diameter, 31" length, and Right Wind configuration, this SSC replacement spring is ready for your repair.

Add this spring to your cart today and restore proper counterbalance with the correct SSC-made replacement.

Before purchasing, double-check:

• .2070" wire size

• 1.75" inside diameter

• 31" spring length

• Right Wind (RW)

If any specification differs, verify the correct replacement before ordering.

Safety Warning

⚠️ Garage door torsion springs operate under extreme stored mechanical energy and can cause severe injury, death, or property damage if improperly installed or serviced.

Installation, adjustment, and removal should be performed only by a qualified person familiar with torsion-spring systems and using proper tools and procedures.

Never loosen winding cones, stationary cones, cable drums, bearing components, or other torsion-system hardware while the spring is under tension unless you understand the correct service procedure.

SEO Title: SSC .2070 x 1.75 ID x 31 Torsion Spring – Right Wind

Meta Description: SSC .2070 wire x 1.75" ID x 31" right-wind torsion spring. Yellow color code, coated oil-tempered wire, cones installed, Made in USA.