RW .2830 x 2.625" x 120" Coated Garage Door Torsion Spring – Right Wind with Cones

Spring Specifications

• Made in the USA
• All springs rated for an industry standard minimum lifecycle of 10,000 cycles
• Springs come with winding and stationary cones installed and are stenciled and color coded for easy identification
• Coated & oil tempered wire

Product Description

The Right Wind .2830 x 2.625" x 120" Coated Garage Door Torsion Spring with Cones is a long-length torsion spring designed for compatible overhead garage door counterbalance systems requiring a .2830 wire size, 2.625" inside diameter, and 120" spring length.

This torsion spring is supplied with installed winding and stationary cones, making it ready for professional garage door spring replacement, spring assembly, and overhead door service work. The coated, oil-tempered wire provides a cleaner appearance and added surface protection compared with bare spring wire.

This is a right-wind torsion spring. It must be matched correctly to the garage door’s weight, height, track setup, cable drums, torsion shaft, cable size, and existing spring configuration. A properly matched torsion spring helps counterbalance the weight of the door so it can open and close smoothly by hand or with a compatible garage door opener.

Size / Specification Chart

Common Uses

This torsion spring is used as part of a garage door counterbalance system. When properly matched to the door, it helps offset the weight of the garage door so the door can open and close safely and smoothly.

This spring may be used for garage door torsion spring replacement, overhead door spring assembly work, professional spring inventory, and repair of compatible residential, commercial, or light industrial sectional garage doors.

Because this is a 120" long-length torsion spring with a 2.625" inside diameter, it is not a universal short residential replacement spring. It should only be used where the spring calculation or existing spring measurements confirm that a .2830 wire size, 2.625" inside diameter, 120" length, and right-wind configuration are required.

Compatibility & Fitment

This spring is compatible only with garage door systems that require a right-wind torsion spring with .2830 wire size, 2.625" inside diameter, and 120" length. Before ordering, confirm the wire size, inside diameter, spring length, wind direction, torsion shaft size, cable drum type, cable size, door height, door weight, track setup, and whether the door uses a single-spring or two-spring setup.

Right-wind and left-wind torsion springs are not interchangeable. Always verify the actual spring wind direction before replacing an existing spring. Do not order based only on the side of the garage door, because spring placement can vary depending on the setup.

The 2.625" inside diameter must match the torsion shaft and cone requirements. Do not substitute this spring for a 1.75", 2.00", 3.75", or other inside-diameter spring unless the full spring calculation and door hardware confirm compatibility.

Important Matching Notes

Garage door torsion springs must be matched to the door, not just chosen by appearance, color, or approximate size. A spring with the wrong wire size, length, inside diameter, or wind direction can cause the door to feel too heavy, open too fast, close too hard, strain the opener, damage cables or drums, or create unsafe operation.

If the door uses two torsion springs, inspect both springs carefully. In many cases, both springs should be replaced at the same time to maintain balanced lifting and reduce uneven wear.

Installation Notes

This spring should be installed only on a properly maintained torsion spring system with compatible winding cones, stationary cones, torsion shaft, drums, cables, center bearing plate, end bearing plates, bottom fixtures, and related hardware.

Before installation, inspect the complete door system for frayed cables, worn drums, loose set screws, cracked bearing plates, bent tracks, worn rollers, damaged hinges, and unsafe bottom brackets. After installation, the door must be balanced and tested manually before reconnecting any opener.

A properly balanced garage door should move smoothly and should not slam down, fly open, drift, bind, or lift unevenly.

Safety Warning

Garage door torsion springs are under extreme tension and can cause serious injury, death, or property damage if handled incorrectly. This product is intended for professional installation only.

Do not attempt to wind, unwind, remove, modify, or replace torsion springs without proper training, winding bars, tools, and safety procedures. Never use screwdrivers, pliers, punches, or improvised tools to wind torsion springs.

RW .2830 x 2.625" x 120" Coated Garage Door Torsion Spring – Right Wind with Cones

Shop a right-wind .2830 wire x 2.625" ID x 120" coated garage door torsion spring with installed cones for compatible overhead door torsion spring systems.