Left-Wind Garage Door Torsion Spring — .2187 Wire × 2-Inch ID × 24-Inch Length, Coated, Cones Installed
Left-Wind Garage Door Torsion Spring — .2187 Wire × 2-Inch ID × 24-Inch Length, Coated, Cones Installed
Spring Specifications
| Winding | Left Wind |
- Made in the USA
- All springs rated for an industry standard minimum lifecycle of 10,000 cycles
- Springs come with winding and stationary cones installed and are stenciled and color coded for easy identification
- Coated & oil tempered wire
Left-Wind Garage Door Torsion Spring — .2187 Wire × 2-Inch ID × 24-Inch Length, Coated, Cones Installed
This left-wind garage door torsion spring is designed for residential and light-commercial sectional garage door systems requiring a .2187-inch wire size, 2-inch inside diameter, and 24-inch spring length.
Manufactured from coated, oil-tempered spring wire, it provides dependable lifting performance when correctly matched to the garage door’s weight and operating system. The winding cone and stationary cone are already installed, making the spring ready for professional installation.
Spring Specifications
- Wind direction: Left wind
- Wire size: .2187 inch
- Inside diameter: 2 inches
- Spring length: 24 inches
- Material: Oil-tempered spring wire
- Finish: Coated
- Winding cone: Installed
- Stationary cone: Installed
- Minimum rated lifecycle: 10,000 cycles
- Country of manufacture: USA
- Quantity: One torsion spring
Product Features
- Precision-manufactured replacement torsion spring
- Coated finish helps protect the spring surface
- Oil-tempered wire provides strength and consistent performance
- Factory-installed winding and stationary cones
- Stenciled and color-coded for easier identification
- Suitable for correctly matched residential and light-commercial garage doors
- Ready for professional installation
Understanding Spring Direction
A left-wind torsion spring is wound counterclockwise when viewed from the winding-cone end.
On many standard torsion systems, the left-wind spring is installed on the right side of the center support bracket when viewed from inside the garage facing the closed door.
Garage door spring layouts can vary. Always confirm the spring’s wind direction, wire size, inside diameter, and length before ordering.
Compatibility
This torsion spring is compatible only with garage door systems requiring all of the following specifications:
- .2187-inch wire size
- 2-inch inside diameter
- 24-inch spring length
- Left-wind direction
Do not select a torsion spring based only on the garage door’s width, height, or appearance. Correct spring selection depends on several factors, including:
- Total door weight
- Cable drum size
- Track configuration
- Standard-lift, high-lift, or vertical-lift design
- Number of springs
- Required spring torque
- Garage door height
A spring with a different wire size, inside diameter, length, or wind direction may not properly balance the door.
How to Confirm the Correct Spring Size
Before ordering, verify:
- Wire size
- Inside diameter
- Spring body length
- Wind direction
- Number of springs in the system
- Door weight or original spring specifications
Measure the spring body only after all tension has been safely removed. Do not include the winding cone or stationary cone when measuring the spring length.
For more accurate wire measurement, measure the combined length of 10 or 20 spring coils and use a garage door spring wire-size chart.
Package Contents
- One left-wind torsion spring
- One installed winding cone
- One installed stationary cone
Winding bars, torsion shafts, center bearings, cable drums, lift cables, mounting brackets, and other hardware are not included unless specifically stated.
Installation Requirements
The replacement spring must be properly matched to the garage door’s weight and operating system. Before installation, inspect the torsion shaft, center bearing, end bearing plates, drums, cables, bottom fixtures, and mounting hardware for wear or damage.
The completed garage door should remain properly balanced when disconnected from the opener.
Installation and Safety
Garage door torsion springs operate under extreme tension and can cause severe injury, death, or property damage if handled incorrectly.
Installation, adjustment, and removal should be performed only by a trained garage door technician using correctly sized winding bars and established safety procedures.
Never use screwdrivers, ratchets, socket extensions, rebar, or improvised tools to wind or unwind a torsion spring.
After installation, test the door balance and inspect the complete garage door system before reconnecting the automatic opener.
Left-Wind Garage Door Torsion Spring .2187 × 2 × 24 Inches with Cones
Coated left-wind garage door torsion spring with .2187-inch wire, 2-inch inside diameter, 24-inch length, and installed winding and stationary cones.
Details
This product is crafted with quality materials to ensure durability and performance. Designed with your convenience in mind, it seamlessly fits into your everyday life.
Shipping & Returns
We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.
We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.
Shop The Full Collection
