#2 Garage Door Replacement Hinge – Standard 16-Gauge Steel Hinge for Sectional Overhead Doors
#2 Garage Door Replacement Hinge – Standard 16-Gauge Steel Hinge for Sectional Overhead Doors
- Category: Hinges
- Fast shipping — same-day on orders before 4:30 PM EST
-
Product Description
The #2 standard garage door hinge is a 16-gauge steel replacement hinge designed for sectional overhead garage doors. It is installed between the second and third door sections when counting upward from the bottom of the door.
The numbered hinge design positions the garage door roller at the correct distance from the door section as the vertical tracks gradually move away from the opening. Its 16-gauge construction is commonly used on lighter residential garage doors requiring stronger hardware than basic 18-gauge hinges.
This hinge is suitable for replacing a worn, cracked, bent, or damaged #2 hinge when the hinge number, dimensions, roller position, and mounting-hole pattern match the existing hardware.
Size / Specification Chart
Specification Details Hinge Number #2 Steel Thickness 16 gauge Hinge Type Standard numbered garage door hinge Installation Position Between door sections 2 and 3 Application Sectional overhead garage doors Typical Door Type Residential sectional garage doors Roller Location End-hinge position Product Number 592 Quantity One hinge Common Uses
- Replacing a damaged or worn #2 garage door hinge
- Residential sectional overhead garage doors
- Lightweight and standard residential door sections
- Correcting a bent hinge that causes roller misalignment
- Routine garage door hardware repair
- Replacing a cracked or excessively loose hinge
- Restoring proper movement between door sections
Compatibility & Fitment
This replacement hinge is intended for garage door locations requiring a #2 numbered hinge.
A #2 hinge is normally installed between the second and third garage door sections when counting upward from the bottom section.
Compatibility depends on:
- The number stamped on the existing hinge
- Hinge width and overall dimensions
- Mounting-hole pattern
- Roller-tube location
- Door-section thickness
- End-stile width
- Existing hardware gauge
- Garage door manufacturer and section design
Confirm that the existing hinge is marked #2 before ordering.
Important Matching Notes
Numbered garage door hinges are position-specific. The hinge number controls the roller offset needed to keep the door properly aligned with the tracks.
Do not substitute a #1, #3, or another numbered hinge for a #2 hinge. Using the wrong hinge number can position the roller too close to or too far from the door, potentially causing:
- Track misalignment
- Excessive roller pressure
- Binding during operation
- Increased operating noise
- Premature roller or hinge wear
- Door sections rubbing against one another
Match the hinge number, gauge, body width, roller-tube position, and mounting-hole pattern to the existing hinge. For best results, replace the damaged hinge with the same style and gauge originally installed on the door.
Installation Notes
Close the garage door completely and disconnect the automatic opener before beginning installation.
Support the affected door section and replace only one hinge at a time to help preserve section alignment. Remove the roller carefully, transfer it to the replacement hinge if it remains serviceable, and secure the new hinge using appropriate garage door fasteners.
Do not overtighten the screws, as this may strip the mounting holes, damage the door stile, or deform the hinge.
After installation:
- Confirm that the roller is properly seated inside the track
- Check that the door sections remain aligned
- Manually raise and lower the door
- Verify that the hinge moves freely
- Listen for rubbing, popping, or binding
- Reconnect the garage door opener only after confirming smooth manual operation
Safety Warning
Garage doors are heavy and may move unexpectedly when hinges or other hardware are removed.
Do not remove or loosen bottom brackets, lift cables, torsion springs, extension springs, cable drums, or other components under spring tension. These components can cause serious injury or property damage if handled incorrectly.
If the door section is damaged, sagging, misaligned, or difficult to support safely, installation should be completed by a trained garage door technician.
SEO title text: #2 Garage Door Hinge – 16-Gauge Steel Replacement Hinge
Meta description text: Replace a damaged #2 garage door hinge with this standard 16-gauge steel hinge for sectional overhead doors. Installs between door sections 2 and 3.
Details
This product is crafted with quality materials to ensure durability and performance. Designed with your convenience in mind, it seamlessly fits into your everyday life.
Shipping & Returns
We strive to process and ship all orders in a timely manner, working diligently to ensure that your items are on their way to you as soon as possible.
We are committed to ensuring a positive shopping experience for all our customers. If for any reason you wish to return an item, we invite you to reach out to our team for assistance, and we will evaluate every return request with care and consideration.
Shop The Full Collection
