The 1-Inch Shaft Collar with Set Screw is designed to fit standard 1-inch garage-door torsion shafts. It provides a secure mechanical stop that helps position and retain bearings, cable drums, couplers and other shaft-mounted components.

The solid one-piece collar slides onto the end of the shaft and locks into position using the included set screw.

Product Features

• Fits standard 1-inch-diameter shafts

• Solid one-piece collar design

• Set screw included

• Durable steel construction

• Provides secure axial positioning

• Compact and easy to install

• Suitable for residential and commercial garage-door assemblies

• Sold individually

Specifications

Common Applications

This shaft collar may be used for:

• Garage-door torsion shafts

• Jackshaft operator installations

• Bearing retention

• Cable-drum positioning

• Shaft coupler positioning

• Counterbalance-system repairs

• Residential and commercial door assemblies

• General mechanical shaft-positioning applications

Compatibility

Compatible with many standard 1-inch garage-door shafts, including:

• Hollow torsion tubes

• Solid torsion shafts

• Keyed shafts where the collar can properly contact the shaft

• Residential torsion assemblies

• Commercial sectional-door assemblies

Confirm the actual outside diameter of the shaft before ordering. This collar is not designed for 1-1/4-inch shafts.

Because this is a solid one-piece collar, it must slide over an accessible end of the shaft. For installations where the shaft cannot be removed or accessed from the end, a split shaft collar may be more appropriate.

Installation

Slide the collar onto the 1-inch shaft, position it against the component being retained and tighten the set screw securely.

Do not overtighten the set screw or use the collar as a substitute for a properly installed bearing, cable drum, spring cone or shaft support.

Safety Notice

Garage-door torsion springs, cables, drums and shafts can remain under extreme tension. Disconnect the operator and release spring tension according to proper service procedures before removing or repositioning counterbalance components. Installation should be performed by a qualified garage-door technician.

1-Inch Garage Door Shaft Collar with Set Screw

The 1-Inch Shaft Collar with Set Screw is designed to fit standard 1-inch garage-door torsion shafts. It provides a secure mechanical stop that helps position and retain bearings, cable drums, couplers and other shaft-mounted components.

The solid one-piece collar slides onto the end of the shaft and locks into position using the included set screw.

Product Features

• Fits standard 1-inch-diameter shafts

• Solid one-piece collar design

• Set screw included

• Durable steel construction

• Provides secure axial positioning

• Compact and easy to install

• Suitable for residential and commercial garage-door assemblies

• Sold individually

Specifications

Common Applications

This shaft collar may be used for:

• Garage-door torsion shafts

• Jackshaft operator installations

• Bearing retention

• Cable-drum positioning

• Shaft coupler positioning

• Counterbalance-system repairs

• Residential and commercial door assemblies

• General mechanical shaft-positioning applications

Compatibility

Compatible with many standard 1-inch garage-door shafts, including:

• Hollow torsion tubes

• Solid torsion shafts

• Keyed shafts where the collar can properly contact the shaft

• Residential torsion assemblies

• Commercial sectional-door assemblies

Confirm the actual outside diameter of the shaft before ordering. This collar is not designed for 1-1/4-inch shafts.

Because this is a solid one-piece collar, it must slide over an accessible end of the shaft. For installations where the shaft cannot be removed or accessed from the end, a split shaft collar may be more appropriate.

Installation

Slide the collar onto the 1-inch shaft, position it against the component being retained and tighten the set screw securely.

Do not overtighten the set screw or use the collar as a substitute for a properly installed bearing, cable drum, spring cone or shaft support.

Safety Notice

Garage-door torsion springs, cables, drums and shafts can remain under extreme tension. Disconnect the operator and release spring tension according to proper service procedures before removing or repositioning counterbalance components. Installation should be performed by a qualified garage-door technician.