Spring Specifications

• Made in the USA
• All springs rated for an industry standard minimum lifecycle of 10,000 cycles
• Springs come with winding and stationary cones installed and are stenciled and color coded for easy identification
• Coated & oil tempered wire

Right-Wind Garage Door Torsion Spring — .2253 Wire × 2-Inch ID × 24.5-Inch Length, Red, Coated, Cones Installed

Spring Specifications

• Wind direction: Right wind
• Wire size: .2253 inch
• Wire color code: Red
• Inside diameter: 2 inches
• Spring length: 24.5 inches
• Spring type: Standard torsion spring
• Wire material: Oil-tempered spring wire
• Finish: Coated
• Winding cone: Installed
• Stationary cone: Installed
• Minimum rated lifecycle: 10,000 cycles
• Country of manufacture: USA
• Application: Residential and light-commercial sectional garage doors
• Quantity: One torsion spring

Product Description

This right-wind garage door torsion spring is designed for sectional garage door systems requiring a .2253-inch wire size, 2-inch inside diameter, and 24.5-inch spring length.

Manufactured in the USA from coated, oil-tempered wire, this spring is designed to provide dependable lifting performance when correctly matched to the garage door’s weight, height, cable drums, track configuration, and required torque.

The .2253-inch wire size is identified by a red color code for easier reference. Color coding is helpful for identification but should not be used as the only method for selecting a replacement spring.

The winding cone and stationary cone are already installed, making the spring ready for professional installation after all spring specifications have been properly verified.

Size / Specification Chart

Common Uses

This torsion spring may be used in properly engineered spring systems for:

• Residential sectional garage doors
• Light-commercial overhead doors
• Single-car garage doors
• Two-car garage doors
• Workshop and storage-building doors
• Standard-lift garage door systems
• Single-spring torsion systems
• Two-spring torsion systems

Actual compatibility depends on the complete spring calculation and not only the garage door’s width, height, weight, or visual appearance.

Compatibility & Fitment

This torsion spring is compatible only with garage door systems engineered for all of the following specifications:

• .2253-inch wire diameter
• 2-inch inside diameter
• 24.5-inch spring body length
• Right-wind configuration
• Compatible torsion shaft and cone bore
• Correct cable drums
• Correct track and lift configuration
• Correct torque requirement for the garage door’s weight

Correct torsion spring selection depends on:

• Actual garage door weight
• Garage door height
• Cable drum model
• Track configuration
• Standard-lift, high-lift, or vertical-lift setup
• Number of springs in the system
• Wire diameter
• Inside diameter
• Spring body length
• Required inch-pounds per turn
• Intended cycle life

Do not select a replacement spring based only on the door size, spring color, mounting position, or visual similarity.

Important Matching Notes

A right-wind torsion spring is commonly installed on the left side of the center support bracket when viewed from inside the garage facing the closed door. Spring placement may vary depending on the torsion-system design.

Always verify the spring’s wind direction directly rather than relying only on its mounting position.

Measure the spring body only after all tension has been safely removed. Measure the wound coils from end to end without including the winding cone or stationary cone.

The red marking identifies the .2253-inch wire size, but the wire diameter should still be physically measured and confirmed before ordering.

A spring with the wrong wire size, inside diameter, length, or wind direction may prevent the door from balancing properly and can overload the opener, cables, drums, bearings, or other garage door hardware.

When replacing one spring in a two-spring system, verify the size, wind direction, age, and condition of both springs. Replacing both springs as a correctly matched pair may provide more consistent lifting force, balance, and service life.

Installation Notes

This spring includes the winding cone and stationary cone. It does not include:

• Winding bars
• Torsion shaft
• Center bearing
• Center support bracket
• End bearing plates
• Cable drums
• Lift cables
• Bottom fixtures
• Mounting fasteners

Before installation, inspect the torsion shaft, bearings, cable drums, lift cables, brackets, bottom fixtures, and attachment points for wear, corrosion, deformation, or damage.

After installation, disconnect the automatic opener and test the garage door manually. A properly balanced door should move smoothly and remain near the halfway-open position without rapidly rising or falling.

The correct number of winding turns and final spring adjustment must be determined from the door height, cable drum configuration, spring engineering, and manufacturer requirements.

Safety Warning

Garage door torsion springs store extreme mechanical energy. Improper removal, installation, winding, or adjustment can cause severe injury, death, or property damage.

Installation should be performed only by a trained garage door technician using correctly sized solid-steel winding bars and established safety procedures.

Never use screwdrivers, ratchets, socket extensions, rebar, or improvised tools to wind or unwind a torsion spring.

Right-Wind Garage Door Torsion Spring .2253 × 2 × 24.5 Inches with Cones

Right-wind garage door torsion spring with .2253-inch red-coded wire, 2-inch inside diameter, 24.5-inch length, coated oil-tempered wire, and installed winding and stationary cones.